Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I have code set up to configure Timer3 to generate a Compare event at 100 KHz, using the PPI so that triggers an ADC Sample event for the two enabled ADC channels. EasyDMA...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hi,
I'm developing an application with a custom firmware image for both the nRF52840 and nRF9160 on the nRF9160DK. I've always been on ncs v2.5.0 and decided it would...
Hello,
I am trying to program a custom device of nrf54l15 using nrf connect for desktop app(V5.2.0) -> Programmer(V4.6.2)
I am able to program it but this is how I see...
I am bringing up a custom board using the nRF54L15 (Fanstel BM15M module) and I am using SPIM00 as the high-speed SPI interface. I am configuring the peripheral through Zephyr...
Using PPK to measure the current, it was found that there was a 1-minute cycle signal in the current waveform. No timer was set. The watchdog timer is 10 seconds.
Im currently working on a project which should receive audio through CIS and retransmit it over BIS. Im using nrf5340_audio_dk for this. Ive tried using https://docs.nordicsemi...
Hi,
We came across this feature " PLMN selection optimization during initial search ", enabled by AT%FEACONF=0,3,1 . It sounds good for speed and power consumption.
...
Hi all,
I’m working on a custom board based on the nRF9151 , and using the Ignion NN03‑320 antenna for GNSS reception.
In our GNSS TTFF testing (using AT commands),...
I'm developing a keyless entry/start system for vehicles with the following requirements:
The vehicle side uses an nRF54L15, while the mobile phone is a standard smartphone...
Hi,
I am developing an audio application on nRF54L15. I have successfully used the Zephyr API to read sequences from the ADC with extra samplings (the "extra samplings"...
Recently I noticed (for reference in the NCS/v3.1.1 SDK) that some nrf9151 boards are in zephyr folder structure and others are in the nrf folder structure.
NRF9151DK...
Hi support:
When testing the peripheral nfc pairing sample on the nRF54L15-DK development board, and using an Android phone for testing, it was found that...
Dear Company
We are using the following component NORDIC NRF52840-CKAA-F-R7 and we have a problem in the test phase.
We have two version with the following marking code...
