Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
I am developing a custom board using the nRF9151 module controlled by an external host microcontroller. The nRF91x1 is running the Serial LTE Modem (SLM) application.
In...
Hi,
I'm using nRF5340 + nRF7002 for project that use wifi but I have issue while reading the default MAC before recording a new one.
The products are tested inside a...
When debugging the exercise 1 application from `Lesson 2 – Reading buttons and controlling LEDs` of `nRF Connect SDK Fundamentals`, I cannot set a breakpoint wherever I want...
Working in a Windows 64 environment with nRF Connect SDK v1.5.0. Target is a custom nRF5340 board connected through a nRF5340-PDK as a debugger, via USB.
I can no longer...
Hi,
I am developing a custom PCB based on the nRF52840 and am currently trying to flash/debug it using an nRF52840-DK (PCA10056) as an external debugger.
connected devices...
Hello
nPM Power UP v 2.24 detects nPM2100 EK, but does not detect the CR2032 battery. The active battery model selected is CR2032 and the fuel gauge is enabled.
I placed...
Hello,
We currently use an nRF51822 device in our product with the top marking QFABC0 .
We understand that NRF51822-QFAB is the ordering part number, and that QFABC0 is...
I'm working on a project for the nRF54L15. Until now I have not been using mcuboot, but since I added SB_CONFIG_BOOTLOADER_MCUBOOT=y to my sysbuild.conf, I get an error when...
in the datasheet table 80 "GPIO port mapping" the function "CAN-RX" is only listed on P9.4 and P2.8 are these the only two pins it can be assigned to ?
I am struggling to...
Hi Dev,
Development platform: NRF54L15 + NCS 3.0.2. We use k_uptime_get() to obtain the system uptime and perform task scheduling. Everything runs normally when the device...
I need to create a firmware to the nRF9151 SMA DK that can send a message to me (it can be via MQTT, but I prefer the nRF Cloud) containing info about the location of the...
Hi,
I'm trying to debug a Zigbee issue and for that I want to try some Zigbee samples on the nRF52840DK. But all links for Zigbee in docs.nordicsemi seem to be broken. All...
I'm running into a bit of an annoying situation every time i run ' west flash --build-dir ./build' in the command line. It rebuilds always after a successful build i set when...
To anyone trying to create the reflector for this combination there is an important conf file to add to the project. You should add android_ranging.conf to your build that...
