first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
The power domains for the nRF70002 aren't very clearly documented in the product specifications, so we're not entirely clear on how we should be connecting the VBAT pin. ...
Hi Everyone,
We are developing a custom retail display solution based on the nRF52810 SoC .
Currently, we are facing an issue where BLE advertising does not start properly...
When my device receives data from the Xiaomi Zigbee switch, sometimes it reboots without any logs.
(Note: Normally, when there’s a bug, the device pushes logs to UART, but...
I was migrating from nrf52832 to nrf54L15, and found that,
ncs3.10 + NRF_SAADC_GAIN1_2 has opposite gain effect on nrf52832 & nrf54L15.
More specifically:
* on nrf52832...
I have started developing a new application based on NCS (previous products still using nRF5 SDK), using the nRF54L15 and I'm struggling with what should be basic tasks. Can...
Hi, I am developing a PCB based on the NRF52840-QIAA-R package.
The pads are very tightly packed, and I had to shrink the size of the middle ground pad to accomodate vias...
Due to the size limitations of the equipment, it is difficult to operate the low-frequency range of 700Mhz to 960Mhz for cellular antennas, and it is necessary to switch them...
hi
> AT+CGMR
mfw_nrf91x1_2.0.2
OK > AT+CFUN=1
OK > AT%XCONNSTAT=1
OK > AT%XCONNSTAT?
%XCONNSTAT: 0,0,0,0,0,0
OK > AT+CMEE=1
OK > AT%XSIM=1
OK > AT+CEREG...
Hi, I am designing a pcb using the nrf52805. In your reference design, the RF matching network specifies a 2.2 nH inductor in 0201 (0603 metric) package.
Unfortunately,...
Hello, We are working on a project based on the Thingy91x which uses the following SAW filter : SAFFB2G45MA0F0A. Unfortunately this part seems to be out of stock everywhere...
Hi
I am maintaining a NRF project, done all Dev Academy courses 2 years ago, still I am havibng trouble.
My current task: I need to set a (hardware) timer interrupt with...
Hi Support
We are in the process of integrating the NPM1304 into a small battery (55mAh) wearable device. I am finding it hard to figure out section 7.3.2
regarding the...
Hello,
I am not able to send any data through the pins of port P2 using Pins : P2.0, P2.2, P2.3, P2.4 , while the pins P1.11, P1,10, and P1.4, P1.5 are working properly...
