This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I am using the command AT+CRSM=176,28539,0,0,12 to attempt to read the FPLMN on the my nRF9160 DK. The modem firmware version is 1.3.5. See attached logs:
(14:11:15.629...
I have built the Matter temperature sensor sample for the nRF5340 running on an nRF7002DK (no WiFi enabled). The power consumption measured with a PPK2 is coming in higher...
Hello,
I am developing Channel Sounding Test Mode functionality using nRF Connect SDK (NCS) v3.1.1 and the nRF54L15 Development Kit (DK) , based on Nordic’s official hci_uart...
I am adding a feature to our device to actively connect to a Bluetooth printer and send data to it, but I am now encountering an issue that I cannot solve.
I currently have...
Hello.
I am considering using the UICR OTP to store device-specific identification information. My understanding is that when accessing this area from a Non-secure application...
Starting from NCS v3.2.0, up to the current NCS v3.2.2, I'm getting back -EIO when trying to use the I2C bus. In commit github.com/.../428ce9f27bc368f8023de98cdd494b060374962b...
Greetings,
We want to use the MCK of the I2S module as a clock output for an external device. For that, we need a freuqency of around 4,096MHz. ACLK originates from the...
HI
I am using the DTM example routine of NCS 3.2.1 and am currently testing the combination of nRF54L15 DK and nRF21540 EK. After flashing the original example routine to...
I’m using an nRF54L15 evaluation board obtained from a distributor and currently testing transmission and reception of large data chunks. I built a vender model and a custom...
General flow when the issue occurs:
1. buf is allocated on prep_pool in prep_write_cb: data -> buf = net_buf_alloc ( & prep_pool, K_NO_WAIT);
2. buf is put to prep_queue...
Hi everyone,
I am currently working on a project using the nRF54L05 and SE052F (from NXP).
I found this GitHub link: https://github.com/NXPPlugNTrust/nano-package/blob...
We are using an nRF52840 running SoftDevice Controller (SDC) in a custom Host + Controller architecture:
SDC runs on nRF52840 as the Bluetooth LE Controller.
Our...
Hi, I run Matter test TC_DefaultWarnings.py but failed the test, see below the last part of the logs:
******************************************************************...
Hello! I am trying to upload 120KB of data through 2 protocols: https and mqtt+tls. Both the cases have same configurations enabled in the context of wifi, net mgmt, network...
Hello, i'm trying to flash mfw-nr+_nrf91x1_2.0.0.zip on a thingy91 x. it doesnt work via nrfutil nrfutil device program --firmwaremfw-nr+_nrf91x1_2.0.0.zip THINGY91X_13A2EC8A4FC...
