After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
In pm_handler_secure_on_connection, I see that it only looks for BLE_GAP_EVT_CONNECTED events if PM_HANDLER_SEC_DELAY_MS is not in use. I also see the comment "In normal circumstances...
The power domains for the nRF70002 aren't very clearly documented in the product specifications, so we're not entirely clear on how we should be connecting the VBAT pin. ...
Hi Everyone,
We are developing a custom retail display solution based on the nRF52810 SoC .
Currently, we are facing an issue where BLE advertising does not start properly...
When my device receives data from the Xiaomi Zigbee switch, sometimes it reboots without any logs.
(Note: Normally, when there’s a bug, the device pushes logs to UART, but...
I was migrating from nrf52832 to nrf54L15, and found that,
ncs3.10 + NRF_SAADC_GAIN1_2 has opposite gain effect on nrf52832 & nrf54L15.
More specifically:
* on nrf52832...
I have started developing a new application based on NCS (previous products still using nRF5 SDK), using the nRF54L15 and I'm struggling with what should be basic tasks. Can...
Hi, I am developing a PCB based on the NRF52840-QIAA-R package.
The pads are very tightly packed, and I had to shrink the size of the middle ground pad to accomodate vias...
Due to the size limitations of the equipment, it is difficult to operate the low-frequency range of 700Mhz to 960Mhz for cellular antennas, and it is necessary to switch them...
hi
> AT+CGMR
mfw_nrf91x1_2.0.2
OK > AT+CFUN=1
OK > AT%XCONNSTAT=1
OK > AT%XCONNSTAT?
%XCONNSTAT: 0,0,0,0,0,0
OK > AT+CMEE=1
OK > AT%XSIM=1
OK > AT+CEREG...
Hi, I am designing a pcb using the nrf52805. In your reference design, the RF matching network specifies a 2.2 nH inductor in 0201 (0603 metric) package.
Unfortunately,...
Hello, We are working on a project based on the Thingy91x which uses the following SAW filter : SAFFB2G45MA0F0A. Unfortunately this part seems to be out of stock everywhere...
Hi
I am maintaining a NRF project, done all Dev Academy courses 2 years ago, still I am havibng trouble.
My current task: I need to set a (hardware) timer interrupt with...
Hi Support
We are in the process of integrating the NPM1304 into a small battery (55mAh) wearable device. I am finding it hard to figure out section 7.3.2
regarding the...
