Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Are there any examples for audio recognition using Nordic Edge AI Lab audio (aka Neuton) ?
I am ready to start creating my model, but was wondering if there were examples...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
Hello
I played with the mcuboot_recovery_entry bare metal dfu sample. I noticed that if I sign an application image with an invalid key (invalid on purpose), the firmware...
I have been reviewing the antenna section in the datasheet of the BLE audio SoC nRF5340. The datasheet mentions a single-ended antenna output (on-chip balun). Could you explain...
Hi,
When the firmware is run in debug mode (J-Link connected), the system always works correctly. BLE initializes properly, and all sensors function as expected.
When...
Hello, everyone. I am an undergraduate student majoring in Mechanical Engineering in South Korea.
I am currently working on a research project to develop a PPG sensor using...
Hi,
(I'm assuming that the main() function of an application is actually executed as a thread.) I can't find any clear documentation that describes how a thread can suspend...
Hello team,
I am trying to interface the AT45DB641E flash with the nrf54l15 on a custom board. I am using the SPI00 instance.
Below is the configuration I set in .overlay...
Hi Nordic team,
We are working on a design that includes more than 50 peripheral node devices, each capturing sensor data and sending it to a single central receiver. I...
Hi,
I'd like to know how to tune the internal capacitance from the 32MHz crystal.
Specifically, I refered to section 4.12.1.1 Using internal capacitors in the nRF5340...
I am using the nrf52840 in QFAA package, and the external DMIC example receives audio data through the PDM interface. I noticed that the official documentation mentions support...
Hello,
We have been testing/validating sQSPI on nRF54L15.
We tested the sQSPI on two versions of our nRF54L15DK (0.9.2 and 0.9.3).
We are using this sample app: https...
Hello. I have one question.
When configuring RAM with the nRF5 SDK + SoftDevice, if I get the following error: APP_RAM_START=0x20006000 --------------------------------...
Hi,
I'm trying to program the nRF52840 Dongle (PCA10059, 2.1.1, 2023.26). I modified the Bluetooth: Central UART sample to use USB instead of UART and built it for the dongle...
I need to use one IO port of the nrf52832. This IO can not only detect the ECG signal but also achieve system off wake-up. The ECG signal is a PWM signal with a duty cycle...
