Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
I am using nRF54L10 with nRF Connect SDK v3.1. The device connects over BLE, wakes every 30 minutes to read sensor data, and then should enter deep sleep (System OFF). However...
Hello, I am currently experiencing an issue with the 802154_phy_test example on the nRF54L15-DK board, and I would appreciate your technical support.
[ Environment ]
...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Hello
I am developpping a product with composite USB (CDC_ACM & HID) and Bluetooth Low Energy, based on a nRF52840 chip.
Can Nordic provides PID free to use for small...
Dear support,
We are connecting with an MQTT server with an expired server certificate. My expectation is that the handshake fails, but apparently the NRF9161 accepts the...
Hello, we are having issues with using the nrf9151DK as a programmer for our own custom nrf9151 board. As the board seems to be locked, we tried to unlock it using the nrfutil...
Hi,
looking through many Posts regarding this topic, i recognized the wiring and labels of the nRF52 DK has changed.
GND is explicitly on the P20 Header anymore.
-nRF52...
Hi everyone,
I'm working on a project using the nRF54 and Zephyr RTOS . Previously, I implemented almost identical functionality on an nRF52, where the device consumed around...
hi:
nRF54LM20A_DK board vscode cannot be programmed.
-- west flash: using runner nrfutil -- runners.nrfutil: mass erase requested
-- runners.nrfutil: reset after flashing...
I am writing regarding an issue I am experiencing with two MDBT53V-1M modules (nRF5340) that I have assembled on custom PCBs. Both modules exhibit identical behavior, which...
I migrate an app from NCS 3.1.0 to NCS 3.2.3.
Using mcuboot with a Thingy:91 or Thingy:91X fails.
flash_img_init results in a flash_img_context, which uses ID 2, the application_slot0...
mcumgr disconnecting when i trying to ble dfu .... " Log from nrf connect mobile app"
nRF Connect, 2026-06-16 FYZKS52_E23993 (E2:39:93:7B:81:AA) V 17:16:59.495 Connecting...
We are trying to bring up a new run of an existing PCB design. No changes in the area of the processor, but a different assembly house. The first call inside ble_stack_init...
We're using two nrf54:s, one DK (initiator) and one custom PCB with 2x antennas (reflector)
I've tried adjusting the samples so that multiple antenna paths are supported...
Hi,
I have a question regarding the SAADC timing parameters.
I could not find an official specification for the SAADC power-up time (t_PWRUP). While measuring it on my...
