Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I am running smp_svr demo on my nrf54l15DK board, and use mcumgr command on my linux.
I could connect to my ble device and echo hello successfully (via peer_name='Zephyr...
The last years I have developed a lot software (low level) for the nRF52840. I like this MCU very much, especially the SHORTS-Registers and EasyDMA are powerful for real short...
I try to get the one button sample to work. There were several details missing to be able to compile and run this sample, which was very frustrating. After editing/updating...
Hello Nordic Team,
I am working on the nRF52833 using nRF5 SDK 17.1.0 and i have implemented OTA DFU in our application. in OTA We have merged all firmware into a single...
nRF52832: Multi node wireless LED synchronization via proprietary radio (nRF5 SDK 12.3.0 on PCA10040)
Summary This post shares a simple proprietary radio demo that synchronizes...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
I am developing a custom board using the nRF9151 module controlled by an external host microcontroller. The nRF91x1 is running the Serial LTE Modem (SLM) application.
In...
Hi,
I'm using nRF5340 + nRF7002 for project that use wifi but I have issue while reading the default MAC before recording a new one.
The products are tested inside a...
When debugging the exercise 1 application from `Lesson 2 – Reading buttons and controlling LEDs` of `nRF Connect SDK Fundamentals`, I cannot set a breakpoint wherever I want...
Working in a Windows 64 environment with nRF Connect SDK v1.5.0. Target is a custom nRF5340 board connected through a nRF5340-PDK as a debugger, via USB.
I can no longer...
Hello
nPM Power UP v 2.24 detects nPM2100 EK, but does not detect the CR2032 battery. The active battery model selected is CR2032 and the fuel gauge is enabled.
I placed...
Hello,
We currently use an nRF51822 device in our product with the top marking QFABC0 .
We understand that NRF51822-QFAB is the ordering part number, and that QFABC0 is...
