Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
On the documentation page for nRF5 SDK for Mesh ( https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK-for-Mesh ) it says that only the nRF52832 and nRF52840...
Hello,
I'm seeking some clarification on a few points to determine the performance of the nRF52840 in high density deployments. The current intended soft device is S140...
Hello,
in the current project we use a large array (16kB) in RAM to store data. After a reset we would like to check if the array is not corrupted to continue processing...
Dears,
I'm using nrf52832 with PCA10040 and SDK 16.0.0,I want to make a DFU via uart. So used the firmware provided in the SDK(nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_dfu_test_images...
Hello,
I would like to evaluate nRF9160 for incoming project.
I have Nordic Thingy:91 with iBasis sim card.
Unfortunately, during configuration it turned out, that...
Hi,
We are using nRF9160 for our application and need to design power supply with battery management IC for it and need to know how much power it will consume with all...
Hi,
I would like to setup my nRF52840-Preview-DK as a central to communicate with a peripheral device via UART over BLE.
Once my peripheral device is connected it writes...
I try to connect NRF9160 dev kit to LTE/NBIOT. But device cannot connect to the LTE/NBIOT network. I am using the at_client example with nRFconnect v3.3.0 LTE link monitor...
I have successfully managed to both provision and configure the simple:_on_of_client.
but i'm having troubles configuring the simple_on_off server. I really have no idea...
Hi folks,
I need of your help. I've developed a new custom board with the nrf52840 CKAA ball assignment and I'm having problems on programming it.
I've developed my...
I am getting errors when initializing the Peer Manager in my code. Here are the items that are unique to my setup:
1) I have a thread which uses fstorage to store a single...
Hi all,
Using the nrf52832 TWI, I am trying to interract with a sensor through I2C.
On the same board, I am successfully able to exchange data with an accelerometer...
Hi Everyone
I have an nRF9160 DK v0.8.2 and I'm running the asset_tracket sample.
I'm from Portugal so iBasis sim card doesn't work here. So I went to Spain and tried...
Hi Guys, trying since some weeks to develop an " simple " Gap advertising with only 2 "service Data" ( battery level and an ID of 4 bytes with an uuid of 128bits with Mbed...
