Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I am a developer of IoT systems working for a private firm within Africa. I currently started the development of a cellular IoT solution and my search landed me on the...
Hi,
I've somehow managed to build the gps sample from source within SES, but I can't get the flashed sample to work properly. Everything is fine if I flash the downloaded...
https://devzone.nordicsemi.com/f/nordic-q-a/46388/nrf9160-dk---make-application-from-scratch
I followed the steps from user: Aakash_Soni on this thread. However, when...
Hello,
I am using Segger Embedded Studio IDE v4.52 (64-bit) to develop an application using nRF5340pdk.
My question is this, I cannot find any of the Preprocessor or compiler...
Hi.
I am developing using nRF52820 with SDK 17.0.0 . I test the USBD using the example code(\nRF5_SDK_17.0.0_9d13099\examples\peripheral\usbd_hid_generic), but the problem...
Hi,
I would like to know if it's possible to read advertising data when connecting to the peripheral.
My problem is sometimes when i read the adv data, and then try to...
Hi,
I try configure 2 gpio pins with opposite pull state, one NRF_GPIO_PIN_PULLUP, other NRF_GPIO_PIN_PULLDOWN :
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_LOTOHI...
Hello
We are working on BLE remote based on nRF52810. We are operating it through coil cell. Please let us know is there Internal battery monitoring feature supported by...
Hi--
I am running a application that executes in the bootloader region of memory (0x70000 to end of memory), and is using FStorage to overwrite the application memory space...
Hello, I am on a NRF9160-DK and I am using SDK 1.3.0 I am working on the AWS_FOTA project. I'm trying to configure the sending of a message in MQTT when pressing a button...
Its a first time, we are using the Nordic product. Please let me know how the step-by-step software installation procedure and would like to know the software cost as well...
I am trying to embed CTS in my code. I have included #include "ble_cts_c.h" Then I made changes to sdk_config.h I have this enabled in sdk_config.h:
Yet I am unable to...
Hi,
I made a demo app using advertising and scanning functionality in SDK 16. Now I'm trying to get it working in our company's full blown C++ framework, which is based...
Hello to everyone, I have a nrf52840 dk device running Zephyr RTOS. I have flash an app to the start address 0x00 and a second app to 0x2000 address. While I am pressing a...
