Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Dear Nordic support,
We are using SDK5 15.2.
Our application uses FDS to maintain configuration. One issue is that we have to change the configuration via phone app regularly...
Hi,
I am working on nRF52840 DK . C:\Nordic\SDK\nRF5SDK17009d13099\nRF5_SDK_17.0.0_9d13099\examples\peripheral\ uart I am sending data from Arduino and showing it on PuTTY...
Hi All:
I try to create a custom Characteristic,with nrf_ble_qwr,
but when set is_defered_write = 1;
connect with NRF_CONNECT APP, I can't write under than 20 byte,if...
Hi, we just saw that %BSKGEN was added in MFW 1.2.1. However, it is not clear to us what is the intended use of it. Could you please give us a bigger picture of it?
Is...
Hi there,
I have a rudimentary understanding of programming with the nRF chipsets and Segger.
In our project, we are trying to locate the position of a transmitter (nRF52833...
when design the product, BLE output power set at +4dBm, and test the real output power with Spectrum Analyzer. when test at the MCU direct output pin the output power is about...
Hello -
We are developing on the nRF52840-DK, using SDK 15.3.0 and FreeRTOS with tickless idle. The SoftDevice is disabled. Using the PPK v2.3.1 when our app is in System...
Hi,
I have nRF9160-DK kit and its environment is set such as nRF Connect SDK and Segger Embedded Studio.
I want to build a simple application from scratch for example...
Hi,
I have a question regarding our approach to achieving high throughput UART transmission over BLE.
The protoboards we are currently testing have BL654 modules from...
Hi !
I tried to connect Thingy:91 to the nrfcloud using iBasis SIM in Germany. I want to try different telecom provider like Vodafone or Deutsche Telekom. Any recommendations...
So as part of my system I have something much like the Nordic UART service in that I need to send a notification when something arrives from the UART. Mine is a little bit...
For a Bluetooth Mesh device, or ' provisioned node ' , does provisioning happen more than once for a established network? Will this device ever need to be re-provisioned once...
Hi,
Is there is a sample for using the nrf-9610 I/O input for A2D to read a voltage across a resistor(using P and N for differential), given that I'm having Zephyr as ROS...
Hello,
A few weeks ago I created a bootloader project from the Nordic documentation: devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader I installed...
Hello,
I use the Blinky example from the SDK. Now I would like to implement an UART on the nRF52840 Dongle. But the program always stops at either nrf_drv_uart_rx or nrf_drv_uart_tx...
