Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
HI all,I am looking for a help.how to start SPIM RX task immediately delay less than 2us？
I have a SPIM test on 52832 DK board(QFAAE0) with SDK16.0, the MISO pin has connected...
Hello
I have a question about the Bluetooth multipairing function using nrf52832. How do I use this feature? And up to how many connections can I make?
Thank you!
I am going to store some informations into UICR.
In case, wrong data wrote have to correct we need to rewrite it.
I have been searched the forum and the answer shows ...
Hello,
It looks like several people are having issues updating the firmware of the Thingy:91 modem with a simple USB cable.
I personally tried on Windows 10, 8 and 7....
Hello There,
I have problems with the installation of the nRF9160. Started the installation earlier and nRF9160 was detected in nRF Connect/Programmer and I could see memory...
Hi, For my application I was using ESB without softdevice and just recently I wanted to add dfu so I had to add softdevice as well. After adding softdevice I found out that...
I want to convert APP_TIMER_TICKS ms to us.
So i'm using this function.
And, the value of APP_TIMER_CONFIG_RTC_FREQUENCY is
Also this is main code.
And, I...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello,
Is there a modified radio test firmware available? I am hoping for something that can be connected to via BLE, command it to turn on a tone, and then reboot the processor...
Hello,
I'm trying to send and receive data between the nRF52832 chip and a phone by following this tutorial:
https://github.com/bjornspockeli/custom_ble_service_example...
Hello!!
We are carrying out a project using nRF52832 , in which we must send a data to a phone every 1 second for 10 hours. The data sent is a sequence of numbers from 1...
I'm using Eclipse CDT for debugging according to the tutorial on this site. I've installed the device pack and I do see the nRF52 peripherals in the debug view. However all...
Hello Out There,
The Getting Started, it states as follows.
The following steps are required for nRF9160 DK versions UP TO v0.9.0. Newer versions of the nRF9160 DK contain...
