I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5ÎĽA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Been working on an unsoldered, untinkered, and in all ways untainted nRF5340-PDK. No jumpers changes. No solderbridges cut. All working fine, but all of the sudden I cannot...
Hi! I want to program a custom BLE application (as Central/master/GATT client device) to run on a Windows PC using a nRF51 Dongle (PCA10031 board) attached through USB in...
Hi,
I am working on the software development of a product based on an nRF52832.
We began our development on the nrf52810 and then moved on to the nRF52832 as it became...
Hello,
I'm struggling to connect to an MQTT-SN Gateway when the device is configured for low power. Currently using MAC-OS Catalina 10.15.3, SES version 4.42 and have tried...
I tried to install the nRF Connect SDK v1.3.0-rc1 error
I open git-bash.exe to execute the ncsmgr init-ncs command, the following error occurred during the installation...
nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager
I am trying to install nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager using nRF...
I am writing a code to blink the LEDS , the 3rd one is not turning off.
Here is the code-
#include <stdbool.h> #include <stdint.h> #include "nrf_delay.h" #include "boards...
Hi,
My device is using nRF52840 with s140 of SDK v16. BLE feature is used with SD .
Sometimes application hard faults in SD are observed in devices deployed. It is quite...
Hello,
I find that after I DFU a new application (using the nRF Connect Mobile App), my device boots into that new application and reconnects to the App, as expected. Then...
Hi,
I am using nRF51822-CEAA with S110 SoftDevice on a custom board which is commercially deployed now. I am using IAR 7.80.2 and Segger JLink Ultra+. I found there are...
Hi community ! I saw a lot of topic about that but i'm working with SDK_Mesh_v4 and i don't get what i want. Does someone have a working example of sending string over Mesh...
Hello!
I have a rather vague question and want to apologize for that beforehand.
I was wondering if it is possible to connect a JPEG camera to the nRF9160 DK (i.e https...
Hi, We are in the production phase of our development, and inadvertently , the mcuboot bootloader set the DCDC on a few units. As described here, https://devzone.nordicsemi...
Problem with setting two uart on pca10040 board
hello
I am reading the log by teraterm by connecting pca10040 board to PC via USB.
I am trying to connect 6pin and...
We are using manufacturer specific data to broadcast data at 10Hz.
We're about to do some testing to evaluate different adverting and scanning parameters to find the best...
