I have a custom hardware running on nrf52840 and using ncs 2.6.1. I have implemented a custom authentication flow with customer characteristic along with the BLE bonding....
Hi ,
I am developing an application which uses nrf52833. I want to perform OTA using 4g module(from Quectel). As per my understanding and explorations, there can be two...
Hello,
I'm using two nRF9161 to communicate with each other and I want to test and measure the differences between the 3 modes available in SDK3.0.0. First, I configured...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
I want to measure the current during sleep,so I write my code as follow:
I queried the manual data that the current is 1.5uA, but 14.0uA is my measuring result. So what...
I am testing the serial interface to BLE messaging using "Bluetooth Mesh Packet Send Opcode: 0xab" - it's working very well. However I have found one thing that is puzzling...
Hello there,
I am working on secure dfu. I followed all the steps mentioned in this post and successfully created the secure .zip file.
Here's what I did(In this order...
First time I programmed the BMD 300 IC ,it got programmed and worked good.After some days later I tried program the board, But the previous code was present in the mcu, i...
When using nrfutil to upgrade the app for 52840dongle, you can see the data shown in the figure through the USB analyzer. The highlighted one does not quite understand the...
Hello,
I'm working on an nRF52832 with SoftDevice v6.1.0 and SDK 15.3.0. We have made a custom application that was created from the ble_app_uart example project. We've...
I inserted code.
OUT 0x04 endpoint works, but 0x84 IN endpoint doesn't.
I use libusb from Linux PC to communicate with nrf52840 via USB. At PC I call function "libusb_bulk_transfer...
I am not able to find the schematics of the development board.
The info center redirects me to the download page of the nRF52840-DK but there are no schematics in the drop...
Hi,
I was wondering if you could give me information on the validity period of the GPS assistance data?
In other words, how often do you need to download the data...
Hello,
I am working developing an application that sends data as notification to connected host at the data rate of 2KB/sec. The chip being used is NRF52832 with S132 soft...
Hello there; My setup: NRF52832 SDK 15.3 I'm facing some problems with FDS when i use it with BLE activated.
When i read or write on FDS using fds_record_open or fds_record_update...
I followed the steps mentioned in the Bluetooth low energy Characteristics, a beginner's tutorial, but at "if ((p_evt_write->handle == p_our_service->characteristic1_value_write_handler...
Hi, I tested "Simple_coap_client" and "simple_coap_server" on NRF52840 using Threading SDK.
I want to change the transmit power, so I used "otPlatRadioSetTransmitPower ...
52810, LIS3DH, I call nrf_drv_twi_tx got NRF_ERROR_DRV_TWI_ERR_ANACK return using either TWI/ or TWIM . Here is my code:
const nrf_drv_twi_config_t config = { .scl = TWI_MASTER_CONFIG_CLOCK_PIN_NUMBER...
Hello,
I want to verify with you if the Standby current for My Bluetooth 5.0 corresponds to the system "on" according to the Bluetooth datasheet or there is another way...
