Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hi! I'm working with a custom board, where pin p0.18 is connected to an external button.
I've read several posts, including this one which say that one must remove the ...
Hi, I'm unable to get a working example with the bootloader, softdevice and application. I'm following this: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts...
Hello There,
i have made an Selfmade PCBA with an nRF52810 and it is my first time that i am working with those Chips.
I have used the reference Design for this board...
Hi
I had a few questions about the nRF52833 SoC.
1. Is there a better way to transfer information through UART rather than using ( printf ) or ( NRF_LOG_INFO ) commands...
I have a similar error as described on https://devzone.nordicsemi.com/f/nordic-q-a/27626/access_model_reliable_publish-returns-nrf_error_invalid_param/109104#109104
I use...
Hi
I build the UartSecureDFU SDK to output a Window's EXE file, it send the upgrading aplication.zip to 52832 successfully in Window 7 System. But If build t he UartSecureDFU...
I have been debugging the TWI master of nRF52832 for a few days now and I have one more problem, which is very weird. For some reason, the master sends only the first read...
I am working with the mesh 4.0 light switch example and had a general question regarding a custom model I created based off the simple on off model.
During configuration...
Hi,
Our application sometimes hits a breakpoint in SoftDevice at either address 0xA60 or (less often) 0xA80.
Based on this post https://devzone.nordicsemi.com/f/nordic...
My question is very similar to this .
I am posting again since it did not seem to be answered.
The error originates from the following:
This happens when I am trying...
IAR IDE can be used to develop and dug the code of nRF52832 . However , IAR IDE can not programme the flash of nRF52832 directly . I need a kind of flash programmer tool ...
Hi all,
I am working with Segger ES on chip nRF52832 with nRF SDK for Mesh v4.0.
I am stuck now at message publication.
I have discovered that my code runs to packet_send...
Hi,
I'm using the nRF52832 with FreeRTOS and SDK 14.2.0 . I took a look at Profiling the Softdevice and FreeRTOS with Segger SystemView and Instrumenting with Segger SystemView...
Hello,
I am using nRF5 SDK v16.0.0 on nRF5232 PCA10040 DK.
I am trying to create an application that will count the number of button presses (GPIOTE events) using a Timer...
Hi.
I'm using nRF52832.
There are some NC pins in my schematics.
How to control them to save current consumption?
Making them output and low is the best solution?
