Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
I created a copy of bluetooth/peripheral example and copied the nRF5340DK board files to make my custom board definitions. The guideby Øyvind A. Sandberg is really good here...
Hello All,
I'm interfacing a temperature sensor ds18b20 with nFR52840, which uses one wire protocol.
I'm using this repo https://github.com/DSysoletin/nrf52_ds18b20_example...
Hello! I wrote my own version of the bootloader for nFR52832. If I go into the loader, check the application and switch to its execution via nrf_bootloader_app_start (), then...
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_clock_init (referred from main.o). .\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_clock_lfclk_request...
I need to adjust the Flash and RAM to accommodate bootloader and Softdefice and read the tutorial at the link https://devzone.nordicsemi.com/nordic/short-range-guides/b/getting...
- I reviewed Android-nRF-Mesh-Library code, and i saw this logic: first, it used Provisioing Service, when provisioning is completed, it disconnected with nrf board, and then...
Hi!
I'm developing code for Central device on nRF52840. SDK 16.0.0 SoftDevice S140.
Peripheral is a Bluetooth mini printer. I can connect to it and print. But when I try...
Does SoftDevice S113 use interrupt priority level 4, or a re the actual S113 interrupt priorities 0, 1 and 6?
As I understand it, this says S113 uses priority levels 0...
nrf connect sdk 1.4.0 and nrf9160 DK
I have made no changes whatsoever.. just opened the project, built using segger and flashed.. fails with "Connecting to google.com connect...
Hello everybody,
I just started using fStorage. When I examine the example, it starts from write address 0x3e000.
err_code = nrf_fstorage_write(&fstorage, 0x3e000, m_hello_world...
Hello
We are developing a unit, based on nRF9160.
In that design LTE switch QM12038 is used.
The manufacturer Qovro has stopped production, so now we are looking for...
I am using the nRF SPI Transaction Manager (nrf_spi_mngr.c) and the SPI transfer (nrf_spi_mngr_transfer_t) isn't performing as expected.
I expect the following code to result...
I'm working in Segger Embedded Studio and NRF52840-dk. The project is configured to work with External Toolchain -> Arm Gnu Embedded Toolchain (9 2020-q2-update).
I've imported...
Hi, I cannot find an SDK17 example for testing Bluetooth 5 extended range functionality. I have found an SDK15 example (after some searching), but surely it is worth including...
I am trying to set up communication between NRF52840 DK and Raspberry Pi 3 using CoAP example given in NRF SDK's IoT examples.
My configuration:
NRF52840 DK - IPv6 CoAP...
