I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I am trying to communicate between my mobile Bluetooth and a BLE sysyem (Bluetooth low energy chip and evaluation board). The BLE chip I am using is NINA-B301 and evaulation...
I experimented with nRF52840 for 1 month. It was uploaded to the board well before, but suddenly I can't get the port.
So after finding a lot of Q&A, 1. Press button-4 ...
I've just moved over to the latest SDK version 1.3.1 (i uninstalled the previous version before installing the new one)
I installed it via the toolchain manager as usual...
Running an application that is using a 32 Mhz SPIM3 interface and it is working fine on our custom board.
As part of the interface testing, a logic analyzer was used to...
According to what I know, the nRF52840 lacks hardware to support AoA as defined in BLE 5.1. Still, the web page of the device mentions that it supports BLE 5.1. What is the...
Hello, I'm trying to send some payload via ELECTRICAL_MEASUREMENT cluster. The sending is realized in the similar way to the zigbee_light_switch example. I'm sending data...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
By measuring with the power profiler kit, we got a system...
I am developing an application that includes custom services. The application is updated by the bootloader. I looked up the post about NRF_ERROR_NO_MEM and modified sdk_config...
Hello, i have a question about program interaction with softdevice and using timeslot API.
I have custom board with nRF52811 chip on it and want to realize peripheral and...
Hello,
I have been playing around with LTE PSM and eDRX modes and had some questions regarding configuration.
If I configure the PSM/eDRX timing windows, how do I know...
Dear All
I want to advertise as broadcaster (not peripheral and also not as a beacon). Advertising packages do not have the information nonconnectable and even if I am using...
Hi,
I'm working through a number of the PCA10040e examples (SDK16 | S112 | nRF52810 - mouse and keyboard to be specific) and have noticed some irregular behavior when waking...
I have the nRF connect application running, but it shows 24 channels, most blue and 3 green. What is the significance of blue vs green? Also, even though I have wifi turned...
I have recently started understanding nRF52840 using SDK v17 and soft device S140 v6.0. I'm using Keil as my dev environment.
Opening any of the SDK example in Keil, when...
Hi,
I am trying to integrate ble based bootloader into my existing system running on nrf52840. I am using SDK 16 v7.0.1 with sd140. To test the process, I have added the...
