In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I was looking through documentation and I noticed that in OPS v0.7.1 the cold start was stated to be -144dBm. In PS v1.1 it calls out -142dBm. Can you explain why they are...
Hi!
I have BMD-350 -A-R and I want to program this by using SWD pins (SWCLK, SWDIO, GND Detect, and VTG) of Nrf52Dk . I make all the connections properly but for some reason...
Hi,
for evaluating purposes I'm trying to send quite big amount of data (100 kB) via socket interface. Sending proceeds fine until approximately 60 kB is transmitted. After...
Hi,
when powering up the nRF52840 PDK its interface MCU LED is blinking fast and the board is not recognized. I've tried to update its firmware by putting the board in bootloader...
On some android phones we have observed that if we try to scan using nRFToolbox for nRF51/ nRF52 controller advertising with UART they do not show up in the scan list. But...
Hello,
I am developing a wireless sensing device using the nRF24L01+ module and I'm planning to use a u.FL connector in my design. I can't seem to find any manufacturer...
Hello,
I am trying to test BLE with SAADC, UART function.
I am complete the ADC test and UART part.
So now, I want to SAADC with BLE and BLE with UART.
The whole connection...
Hi all,
I tried to follow this tutorial to be able to use GDB as debugger but failed right in the beginning because JLinkGDBServer could not connect. Here's the log I get...
Hi , i am using the nrf52dk and i have a switch statement that depending on the case there is a set of enum and i would like to utalised the push button to increase/decrease...
sir, i am attempting to compile a solution from github(nrf calender) but i could n"t.Tell me where should i put the file and how to compile to make it work??
Hello,
I have a question: how can i make applications for Nordic Thingy:91, and upload them to it? (I am a total newbie when it comes to Nordic products and IoT, i am not...
Hi All,
I am developing one project and there we are using ADC (i.e., SAADC in nRF). I have designed the hardware where I am using Capacitor ( C14, 2.2µF) which is connected...
Hi. I have a nRF52840 setup using the PWM driver, and it is outputting a 50Khz pulse 50% duty cycle.
How do I modify the sequence values so that I can modulate this 50Khz...
Dear all,
I would like to implement the IEEE 802.15.4 stack, using the driver inside the SDK for Thread and Zigbee. Unfortunately there aren't any examples ad so everything...
