I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
We're thinking of attaching a battery in the manufacturing process but they may not be programmed right away. Do empty nRF52 modules go into sleep mode when there is no program...
Hi
how to connect one peripheral to two central and after connection established sent the data to both central?
I am using nrf52, soft device 132 .
i am able to make...
Hi!
The nrf5340 PDK I've purchased does not have a mounted "nRF USB" (J3) port, only the debug (J2) port.
Is it possible to do raw USB communication with the USBD driver...
Dear Sir.
I am using the Timer of nRF916 .
In a simple project the timer is working fine ( see attached code ).
A buzzer is connected to PWM output pin 12.
I can...
Dear Sir.
Attached a code .
It takes about 20 seconds from power on until the Blue Led is On.
The timing of the Blue Led is about 2 sec , as in the code.
Commenting...
Hello
I use sdk v17 and nRF52DK. I want to use mpu6050 sensor in the example of ble_app_uart. SDK provides a driver for mpu6050, but I am not good enough to use it.
https...
Hi, I'm a beginner with these Nordic DKs. I'm just trying to connect it to my computer and get familiar with the hardware and firmware. However, when I plug in the DK via...
i want to store and retrieve data in flash. i followed steps as in the sdk infocenter but i am not getting the interrupt after fs_store(). Actually return value of fs_store...
Hi,
In my current project based on SDK 15.3 and sd140, I am using nrf52840 in both peripheral and central devices. I need to be able to maintain 10 concurrent connections...
Hi i am using the nRF52dk and i am trying to control a bldc can anyone help me to guide in how i can generate a pwm to get a sin wave
best regards Nikolai
Currently I want to build the light_switch examples from the nrf5_SDK_for_Mesh_v4.2.0 on my nrf52840 dev board but this gives the following error "boards.h: No such file or...
Hi,
I am working on a project of throughput data from sensors to my central via nrf52805 through a notifying service (SDK16.0.0).
Symptom description
We have app from...
Hello,
I want to use I2C slave on nrf9160, but there is no I2C slave driver implementation.
So I read that instead of this, I can use nrfx twis drivers on nrf9160.
I...
What am I missing when
NRF_SPI_MNGR_DEF(my_spi_mgr, 2560, 0);
causes:
../../../../../../integration/nrfx/legacy/nrf_drv_spi.h:120:37: error: 'NRF_DRV_SPI_INSTANCE_0...
