Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using pin 27 as SCL and 26 as SDA on my custom board which is working on 1.8V.
There is no activity on SCL pin, while i am getting correct values on SDA pin when...
How can I read the ICCID (Integrated Circuit Card ID) of the SIM-card?
Normally (with competitive modems) I get the CCID by AT+CCID.
The nRF9160 reponds with +CME: 0 ...
Hi, I would like to develop a BLE central node that sends over UART when a button is pressed. I understand the memory is limited on nRF52810, but I think it'll fit. The example...
I am developing on the nRF52832. I just discovered that if my program enables Access Port protection by writing the UICR at runtime, then the program can still be read out...
Hello,
I want to use a third party bluetooth module (based on Nordic SOC) in my application, so far my understanding is that using your softDevice stack I have to implement...
Hi
My Thingy:52 works perfectly OK with Thingy app on my iPhone.
However when I use the Gateway on my iPhone and then nrf cloud I get an unstable connection on the cloud...
Hello Developers,
I have just started playing around with BLE Mesh Zephyr examples on my recently purchased nRF52840-PDK board.
Anyways, I am bit stuck with one fundamental...
Hi,
I've used the nRF51822 in the past to make sensors that connect to a mobile device. Basically it worked just like every other non-mesh BLE device:
1. It advertised...
Hi:
I'm developing a project with nRF 58232 in ble_app_hrs_rscs_relay example ( s132 sdk:nRF5SDK160098a08e2 ). The device need to be central and peripheral,My device worked...
Hi there,
I'm planning and hoping to use the nRF52840 (in module form) for an upcoming medical device design.
This will need to interface to a PC/Mac/Linux to send specific...
Is APP_TIMER_V2 supported by Mesh SDK 4.1? According to this forum, v2 should fix all sorts of issues related to v1. But it seems that app_timer_mesh.c is only partially compatible...
Hey,
I am working on a version which is uploaded from a bootloader (DFU), the bootloader print to UART and uses the UART libraries.
I want the application to close the...
Hey,
I am working on nRF51822, SDK12, S130, I wish to get more data into my advertising packet, however there is not enough space, I was thinking to COMPLETELY remove...
The goal is to be able to automate build using CMake. I am evaluating this by trying to build example project in nrfSDK 16.(I chose saadc example from nRF5_SDK\examples\peripheral...
