Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Hi all, I'm developing nRF52832.
My goal is to send ADC data to central device using BLE.
Below is part of my code.
Maximum MTU size is 251.
I sent data in 16...
Hello,
nRF52-DK (PCA10040) has two mysterious 12 pF capacitors C52 and C53 connected to P0.25 and P0.26 respectively (see attached picture).
Is there any special purpose...
I'm using nRF52DK with ble_app_hids_mouse to pair with the smartphone.
From the smartphone we can disconnect the device at will. But I have problem when I want the device...
Hi All,
Looks like develop nRF52840 on SDK16.0 required
NordicSemiconductor.nRF_DeviceFamilyPack.8.27.0.pack
But there is no such pack on http://developer...
Dear All, I am trying to measure the current consumption for the nRF52840 USB Dongle. I intend to use it as a beaconing device and attach it to a battery.
At the moment...
I have recently switched to using SEGGER embedded studio (SES) which seems to be advocated by Nordic. I have arrived from Eclipse which though extremely flexible is complex...
Hello,
I am working with the nRF52840 dongle. There is a bootloader at the end of it's flash, which can be started by pushing reset after power up.
However I cannot start...
Hi Gene,
One of my customers using our module to pilot run.
https://static1.squarespace.com/static/561459a2e4b0b39f5cefa12e/t/5da77e178970da0cc270ef0d/1571257883383...
Hello,
I noticed that Table 7.3 of nRF52832_PS_v1.4.pdf states that 37 interrupts have been implemented, whereas the peripheral listing in the documentation as well as interrupt...
While advertising I could see some increased current peaks on one of the three channels. Its random and is observed mostly at the first or last channel of advertising.
Any...
Hi,
I wish to power optimize the proximity example application, as my intention to make a find-me tag. So I may not need the lls and tps services. Is any guidelines for...
Hi There,
I now have 4pcs PCA10056 and 4pcs PCA10059 for the development of our BT Mesh products by nrf52840 of Nirdoc. I have completed the installation of the tool chain...
Hi, I wanted to send data over Bluetooth 5.0 modules and to see on a terminal. So I used nRF52840 DK as central device ( ble_app_uart_c) and Fanstel modules ( ble_app_uart...
HELLO ALL,
I'M TRYING TO TEST THE BSC Rx EXAMPLE FROM DE SDK V16.
WHEN I DO IT USING ANTware II, EVERYTHING IS OK, SINCE IT'S ENOUGH WITH CONFIGURING CORRECTLY CHANNEL...
Hello,
This is a followup question regarding this old thread I started: https://devzone.nordicsemi.com/f/nordic-q-a/48295/hold-output-pin-during-bootloader-jump
IC: NRF52840...
