Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Dear All, I am trying to measure the current consumption for the nRF52840 USB Dongle. I intend to use it as a beaconing device and attach it to a battery.
At the moment...
I have recently switched to using SEGGER embedded studio (SES) which seems to be advocated by Nordic. I have arrived from Eclipse which though extremely flexible is complex...
Hello,
I am working with the nRF52840 dongle. There is a bootloader at the end of it's flash, which can be started by pushing reset after power up.
However I cannot start...
Hi Gene,
One of my customers using our module to pilot run.
https://static1.squarespace.com/static/561459a2e4b0b39f5cefa12e/t/5da77e178970da0cc270ef0d/1571257883383...
Hello,
I noticed that Table 7.3 of nRF52832_PS_v1.4.pdf states that 37 interrupts have been implemented, whereas the peripheral listing in the documentation as well as interrupt...
While advertising I could see some increased current peaks on one of the three channels. Its random and is observed mostly at the first or last channel of advertising.
Any...
Hi,
I wish to power optimize the proximity example application, as my intention to make a find-me tag. So I may not need the lls and tps services. Is any guidelines for...
Hi There,
I now have 4pcs PCA10056 and 4pcs PCA10059 for the development of our BT Mesh products by nrf52840 of Nirdoc. I have completed the installation of the tool chain...
Hi, I wanted to send data over Bluetooth 5.0 modules and to see on a terminal. So I used nRF52840 DK as central device ( ble_app_uart_c) and Fanstel modules ( ble_app_uart...
HELLO ALL,
I'M TRYING TO TEST THE BSC Rx EXAMPLE FROM DE SDK V16.
WHEN I DO IT USING ANTware II, EVERYTHING IS OK, SINCE IT'S ENOUGH WITH CONFIGURING CORRECTLY CHANNEL...
Hello,
This is a followup question regarding this old thread I started: https://devzone.nordicsemi.com/f/nordic-q-a/48295/hold-output-pin-during-bootloader-jump
IC: NRF52840...
Hi,
I'm relatively new to your product line, but have been spending a bit of time trying to bring the volume control functionality into a SDK16/PCA10056/s140 configuration...
Hi,
I am using SD calls to start an advertisement of BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED :
sd_ble_gap_adv_start(m_adv_handle, APP_BLE_CONN_CFG_TAG...
Hello, I have a project that's fairly mature and working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a million...
Hi
I plan to use nrf52 DK to program my device by using a connector https://www.tag-connect.com/product/tc2030-idc-nl
But should I connect it to debug in or debug out...
