I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello, We have a custom board with nRF52832, using BLE, s132. I have noticed recently that in nRF Connect App (v4.29.1) usually the services and characteristics show up twice...
Hi there,
I am trying to develop a simple application that must write information within a micro SD card (nothing too fancy, it is just plain data read from the internal...
Hi,
I added MCUboot and SMP BT Service to the OpenThread CLI routine to implement the device firmware upgrade function.
I found that after DFU is completed, the Thread...
If the lock's status changes while the device is powered off, causing a mismatch between the lock and the Apple Hub, how can I immediately update the status upon powering...
Hi!
I cannot get I2S echo sample to work on nrf54L15. Tried following overlay
build configuration nrf54l15pdk_nrf54l15_cpuapp
I verified with oscilloscope that no...
Hi,
All-of-a-sudden I'm having problems debugging my application. THis morning it was working right, this afternoon it's gone wrong!
I think it's pretty near using up...
Hello,
we want to get three different states using only one GPIO:
1. nRF52840 GPIO output driven low
2. nRF52840 GPIO output driven high (3V3)
3. nRF52840 GPIO internal...
Hello Nordic community,
I'm working on a project using the nRF5340DK where I need to achieve precise control over three GPIOs with the following specifications:
P0.07...
Hello,
We are using the nRF52840 on our own board.
When I added up the current consumption at 3V, based on the datasheet, I get 14.3mA (CPU from RAM, Tx at 0dBm 1Mbps...
Hello,
I'm using peripheral_past sample on nrf5340 audio DK board, and select nrf5340dk_nrf5340_cpuapp_ns for Build Target.
I added the following config to enable RTT...
Hello,
I have nRF9160, modem FW = 1.3.6 and nrf sdk version 2.7.0.
I am trying to create an outgoing socket with connects to specific port num and ip address but I am...
Hello, I am working on a project where we use MCUBoot.
Currently everything works fine, but now we wanted to introduce persistent storage of some key value pairs.
For...
Hi Nordic Team,
What is the difference between 10 bit, 12 bit and 14 bit operation mode and 8/10/12/14 bit resolution in SAADC of nRF54L?
Best regards,
Bhavya
Hello,
I'm using nRF54L15DK and nRF Connect SDK 2.9.0. I'm developing a project for PID control of the temperature of a peripheral, let's say a heater. The feedback is...
