I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
I am currently conducting measurements using channel sounding with my nRF54L15 boards. I am at the end of my master thesis, so there is not so much time left to really...
Hi
I am using an nRF54L15 and trying to use pins for I2C, but to do this I have to disable the NFC pins.
I did the following:
But that wasn't enough.
I noticed...
Hi team, After executing RRAMC.ERASE.ERASEALL with an external debugger, I was unable to access the CPU (board) after reset. To resolve this issue, I connected the nRF-programmer...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Dear Customer Support,
Wanted to open a case to follow up on this old one Case ID: 335484
I initially looked at the counter alarm under
https://github.com/zephyrproject...
Hello, I would like to ask if the latest SDK version supports power management on the FLPR core of the nRF54L15. According to this article, the power consumption is quite...
hello everyone I have implemented BLE, ADC, RTC, and UART. After that, my power consumption is around 1.31 mA. Can you suggest possible ways to reduce power consumption or...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up to read the potentiometer's raw value . As part...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
Hello Nordic Team,
I am reaching out to ask for some advice and/or guidance on how I may debug code that:
1. Is initialized and runs BEFORE main
2. Is part of the zephyr...
Hello,
we are developing a device which implements BLE hid keyboard. The code is based on the hid keyboard example in the NRF Connect SDK.
The example uses battery service...
Hello,
I am planning on using the WLCSP version of the nRF52840 chip on a PCB design. ( nRF52840 - Bluetooth 5.3 SoC - nordicsemi.com )
Is it possible to program the nRF52840...
I'm attempting to write software onto a newly purchased nRF52840 dongle using nRF Connect for desktop, but I'm unable to do so. My environment is Ubuntu 24.042 LTS. The LED...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
