I am currently creating and testing a custom board equipped with the nRF9160 and the P822601 antenna. Considering future development, it is expected that another external...
Title: nRF54L05 issue after migrating from NCS 3.0.0 to NCS 3.3.0 with PM static partitions and MCUboot external-flash secondary slot Description: I am migrating a project...
I am currently designing a custom board for my nRF54L15 project and I would like to know if the "Antenna" pin on the nRF54L15 can have a DC path to ground/ground layer of...
I have a nRF54l15dk development board and a custom nRF54L15 board that I am trying to load a Matter Template sample application on. I have created a custom board device tree...
I have observed that when using the ESB protocol at maximum throughput, the measured power consumption decreases as the PHY data rate increases: 4 Mbps consumes less power...
Subject: Connecting LPCOMP CROSS event to TWO DPPI-driven tasks (GPIOTE toggle + TIMER count) simultaneously — only the last-configured one fires
Chip: nRF54L15 SDK: nRF...
Dear Nordic, i have started my application with toolchain & sdk both v3.3.0, using custom services & charachteristics, with BLE advertising @500ms interval works fine. but...
I am new to NRF chips and trying to read, write, and erase to flash using nrf_fstorage. I have looked at the example project flash_fstorage and I am able to successfully read...
Hi All,
I'm trying to generate an interrupt on the X PWM's falling edge. My idea was to setup the PWM and count the number of falling edges using PPI & a timer / counter...
I have following code fragment to enter nRF52 into power-off mode. There is s132 softdevice 3.0.0 running and my SDK is 12.0.0:
int32_t ret = sd_power_system_off();
...
Hello,
I am having an issue viewing serial communication from the nRF9160 on the LTE link monitor. I am able to view output when the code is compiled from a different...
After burning the application, the following operations were performed: nrfjprog.exe -f NRF52 --rbp ALL nrfjprog.exe -f NRF52 --pinreset
There are a total of 600 devices...
Hi everyone,
I have setup a Bluetooth Mesh network of 5 Light Control Server Nodes and 5 Low Power Nodes that have friendship with eachother.
All nodes publish and subscribe...
I'm facing the requirement to save few kb of data in flash and process it over time. Because none of the standard mesh models fit, a custom mesh model will be the only option...
Hey,
I encountered a very strange problem while I was trying to connect from nRF52832 (as a central device) to my nRF52805 as a peripheral. If I am trying to connect to...
Hello,
I am working on a custom development board that is using the nRF52840. After programming the nRF52840 on the board with Soft Device s140_nrf52_7.0.1_softdevice.hex...
Hello DevZone,
A product I use uses NFC tag type 2 to communicate. It usually communicates to a separate chip but I want to replace this with the nRF52832.
I opened...
Hello,
I'm working on a product where we want the nRF52840 to be able to reset itself in hardware . This is currently done via an IO that drives a SHUTDOWN# signal into...
Hi,
I'm using TWI to control accemeter(MMA452).When I used TWI SENSOR to read my sensor, it didn't work normally.
The address of MMA8452 is 0x1C,so i want to read...
The separation of flash memory into a region for the application core and one for the network core on the nRF5340 seems rather cumbersome and error-prone.
I'm especially...
Hi,
will qmi_wwan or gobinet driver be available for nRF9160? PPPD is not available. It is quite a limitation in use to miss ethenet interface based connectivity.
Regards...
Hi everyone, I’m have a wired network of 1000 devices (relay switches) that I’ve been tasked to upgrade to wireless.
Devices are inside a warehouse, about a pallet apart...
