I am Using SPI4 in nrf5340 and I am trying to put SPI in low power mode when not in use. How can I do that?
Here is the code given:
aliases {
displayspi...
I am currently creating and testing a custom board equipped with the nRF9160 and the P822601 antenna. Considering future development, it is expected that another external...
Title: nRF54L05 issue after migrating from NCS 3.0.0 to NCS 3.3.0 with PM static partitions and MCUboot external-flash secondary slot Description: I am migrating a project...
I am currently designing a custom board for my nRF54L15 project and I would like to know if the "Antenna" pin on the nRF54L15 can have a DC path to ground/ground layer of...
I have a nRF54l15dk development board and a custom nRF54L15 board that I am trying to load a Matter Template sample application on. I have created a custom board device tree...
I have observed that when using the ESB protocol at maximum throughput, the measured power consumption decreases as the PHY data rate increases: 4 Mbps consumes less power...
Subject: Connecting LPCOMP CROSS event to TWO DPPI-driven tasks (GPIOTE toggle + TIMER count) simultaneously — only the last-configured one fires
Chip: nRF54L15 SDK: nRF...
Dear Nordic
Q1.
We tried new nrf9151 IC at custom board.
IC version: nrf9151 AEA (Engineering B)
Firmware: ncs2.7.0 Serial LTE modem application + mfw_nrf91x1_2.0...
hi,
When verifying the modem upgrade, if the network type is set to support both Cat-M and NB (AT%XSYSTEMMODE=1,1,0,0), the actual network that connects is NB, and the modem...
I have 3 nrf boards connected. 2x nrf52832 and 1x nrf5340.
esb_tx is running on nrf52832(682782977) esb_rx is running on nrf52832(682497942) & nrf5340(1050025410)
west...
Hello
I have a custom nrf52840 board with an external 1MB NOR flash
The app uses MCUboot for DFU
I know I can define the external flash in the pm_static.yml for the...
We are currently working with the nRF52832 Development Kit and are aiming to interface an ISO15693 NFC reader using the PN7150 NFC module. We intend to communicate with the...
Are there any serial commands that I can use to control some the functionalities of the board. My task is to use the dk with a windows app (UWP, C#), I want to start stop...
I tested it on the lzma example (ncs\v2.8.0\nrf\tests\subsys\nrf_compress\decompression\lzma),on the Cmakelist.txt code
generate_inc_file_for_target(
app
${ZEPHYR_NRFXLIB_MODULE_DIR...
We have a production system running a modified asset_tracker_v2. Things are basically running fine but there is question with downlink and FOTA operations. We publish a JSON...
I am trying to get mcuboot working on a custom board. on version 2.7.0 sdk, But the board is not found.
I have simplified it to a minimal version like so (my folder can...
I am evaluating external flash on nRF5340DK. When I'm doing appcore DFU from external flash so that mcuboot_secondary and settings_storage are located on external flash, everything...
Hello!
I am returning to software development for a BLE Mesh project on the NRF52840 after being focused on the hardware development for several months. I see that NCS is...
Hello
I am evaluating Wi-Fi location using the nRF7000 and nRF9160.
For the initial test, I used the nRF7002 Expansion Board. I soldered wires to it and connected them...
What would be the certification cost for developing small volume Zigbee or Matter+Thread applications using nRF modules and nRF Connect SDK? Is this eligible to certify via...
Hi experts,
I followed the instructions the Readme file described. It almost works well. But I still found two issues:
the Startup time is too long when pressing the...
