Hey,
I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0.
According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
We urgently need to add support for Band 40 (B40) to our product. Our use case is very specific, and as far as we understand, the NRF91 currently does not support B40. We...
i just rebuilt the code in the beacon_advertiser.zip file attach to this issue for the NRF52232....
the code runs as expected, though consumes about 200uA when sleeping...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
Hi,
In my project I am developing a system to monitor the consumption of electricity taken from the grid. The nRF9160 SiP module is responsible for acquiring analogue signals...
Hi,
USB CDC EPOUT stops working as the USB incoming traffic data rate increases. The symptoms of this issue align with the Errata 199. The workaround for Errata 199 is...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
I just flashed a new image on my device using MCUmgr. In the logs, when the device boots up, it shows the correct APP_VERSION string.
returns:
I: Firmware version: 0...
Hi, We are trying to provide example support for our RAK4631 (nRF52840 based) and an ultrasonic PDM microphone (RAK18032). We have been able to get a sample frequency of 100...
Hi, I am using nRF5340 for my unicast Audio server example where the nRF5340DK is the headset and my mobile device is the audio source. I have taken the unicast audio server...
Hi,
I just can not download nRF_DeviceFamilyPack 8.44.1 from this link developer.nordicsemi.com/.../ It comes up an error of the server. Does any body knows how to get this...
It seems the "reset" button on my nrf52840dk doesn't do anything anymore. I believe this started happening after I enabled mcuboot in sysbuild. Is this expected?
I'm following the tutorial Exercise 1 – Custom board for single-core SoC using ncs v2.9.0 with one slight difference in that I'm using a nRF52DK with nRF52832 because that...
Hi,
In my project I am developing a system to monitor the consumption of electricity taken from the grid. The nRF9160 SiP module is responsible for acquiring analogue signals...
I built a custom board with the nrf5340 and a SD card connected to non-standard gpios. My SD card is connected via SPI over the P0.14, P0.15, P0.16, P0.17, respectively for...
The latest toolchain has removed "serverArgs": from debug configuration in nrfConnect 2025.4.106
Is is mandatory as we only have RTT on our FF board and no serial...
Hello everyone,
I am trying to test the SLM on the nRF9160DK on NCS 2.9.0. (SDK and toolchain) I want to control the nRF9160 with an external MCU, so for this the application...
Hi! I am developing project with nrf connect sdk 2.9.0 on nrf9160 platform. This is multi image project (b0 + mcuboot + tfm + non-secure application). I needed to configure...
Hello,
Our product that we currently design is based on the nRF52840 QFAA and w e are looking to achieve FCC, CE and RED compliance.
I would like to request any certificates...
Hi.
For a while I have had some issues with the toolchain when using the nRF connect SDK in visual studio code on windows 10. I believe it was after installing SDK version...
Hi,
I'm working with the nRF54L15 SoC and running into an issue when using UARTE21 together with SMP over Bluetooth . Here's what I’ve observed:
UARTE21 works perfectly...
Hi,
I have an issue with nRF Kconfig GUI in VS Code.
My prj.conf is empty, and the _defconfig file of my board contains this:
When I open the GUI and...
