Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
Just need a quick checking on this.
Currently we using nRF5 SDK, after production, is it possible we OTA update the firmware which using nRF Connect SDK?
This...
Hi,
I tried to build and programm this DTM example from this SDK example: ncs\v1.6.1\nrf\samples\bluetooth\direct_test_mode
I got this following error. Do you know where...
Hi,
With the NRF Connect / NCS SDK, I can build the asset_tracker and serial_lte_modem without issue.
I want to make my own project, so I copied asset_tracker entirely...
Again I am asking a question I should not because I cannot find it documented.
I get a pairing request from the central. I need to respond with sd_ble_gap_sec_params_reply...
Hello.
Now, I'm trying to make a Beacon with updatable Major Value, based on sample 'ble_app_beacon'.
I'm not really familiar with BLE and Nordic device, though...
I...
Hi,
We have created GATT servers and tried to connect with one MOBILE APP.
But, we failed.
Although, we could able to connect with standalone BLE, but once we tried...
Hi,
I have been trying to experiment with the nrf5 SDK for thread and zigbee. Our product uses a NRF52840 in the form of a BL654 module and we have been using xbee S2C modules...
Hello, I was reading through the documentation for the nRF Connect for Desktop and I came across a reference to set up the nRF Connect for VS Code. However, I couldn't find...
Hi,
I am using nRF52820on a customer board to run MESH Light project, but I can not start the mesh stack, problem is:
it looks like due to flash limited, but according...
Hi All,
I am new to Zephyr/NCS, so I am a little confused about which UART driver (Zephyr's uart/nrf_libuarte/nrfx_uart/nrfx_uarte) to use to approach this feature with...
I'm evaluating the nRF52840_DK with nRF5_SDK_17.0.2
After doing some tests with ppi to timestamp gpio events, I'm now enabling the softdevice.
This leads to two questions;...
I have been successfully using mergehex with s140_nrf52_6.1.0_softdevice.hex and a bootloader to create firmware packages for my nRF52840-based device and wanted to try softdevice...
When I run the QSPI example in SDK, it can work well both on the PCA10056 and my custom development board. However, when I transfer the example to app_buttonless_dfu, the...
Hi,
I am trying to send the max 240 bytes in NUS SERVICE nRF_CONNECT_SDK
I have seen the ble throughput example and changed
CONFIG_BT_RX_BUF_LEN=255
CONFIG_BT_CTLR_TX_BUFFER_SIZE...
Hi Nordic
We are evaluating nRF 9160 for our next revision of the PCB, and we are testing nRF9160DK.
It came with a sim, which i tried to activate by nRF cloud, but it...
