Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I'm getting an undocumented status value back from nrfjprog when I try to program my dev board:
ERROR: command exited with status 3221225477 : nrfjprog --program C:/mdsg...
Hi,
I'm new to Nordic tools and am stuck on getting all the pieces in place. I have:
Mac OS 10.14.6
nRF Connect v3.6.1 Getting Started Assistant
Python 3.6.3
All...
Hey Guys,
Transferring emulated project
Transferring an emulated project to the nRF52810 SoC,
If you have developed your application using the emulated project...
Hello,
I am trying to setup a Project with nrf25840 by using the nRF IEEE 802.15.4 radio driver in multiprotocol mode with ble. ( https://github.com/NordicSemiconductor...
Hii guys ,
I have a customised nrf module based on nrf52810 . I have dumped ble_app_beacon code and it works fine but when i dump ble_app_uart example code then i am not...
Hi
I have a question about peers deleting.
It is saying in documentation about pm_peer_delete:
"Warning Use this function only when not connected to or connectable for...
hi Support team,
I have one problem with window7 system both 32 bit and 64 bit, that the usb cdc driver can not be verified by windows, that software signature is not right...
hi support team,
customer has one question about TWI electricity. in the IIC spec the "tLow " should be more than 1.3 us
however, our chip interface TWI timing " tLow...
Overlapping segments detected at address 520192.ERROR: The hex files cannot be merged since there are conflicts.
should be
Overlapping segments detected at address 0x...
I’m obviously missing something from the information I’ve gathered with respect to designing a co-planar waveguide, PCB 50 Ohm transmission line. The calculations I get differ...
Hi everyone,
I've been working on the firmware for a BLE keyboard, this is my first big project using the nRF5 SDK and everything's been going great so far. I'm using...
nRF5 SDK for Thread and Zigbee v4.1.0 documentation states that only application can be updated over Thread Secure DFU. However, nRF5 SDK for Thread and Zigbee v2.0.0 documentation...
Hi,
I am running an nRF5 SDK BLE example ( Cycling Speed and Cadence Application ) on nRF52 DK as peripheral and connect to nRF connect mobile app as central, and I would...
I use the thingy 52 with the nrf52832 and the SDK13. I want to scan every 30 seconds and receive packets from other thingy's but I can't find how to initialize my scanner...
I can only see the conf files and other yaml files when i open nrfconnectsdk sample in Segger embedded studio IDE.Where do we exactly write our application code?Application...
