Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello,
I'm using nRF52832, SDK15.0.0, Softdevice S132.
What should be the code added to application in order to support BLE DFU service?
I've been here , but its for...
hello,
I want to use RSSI on nrf52832, and the project is uploaded.
the question is, I test the RSSI on channel 2468MHZ， the NRF_RADIO->RSSISAMPLE result is about -92dBm...
Hi,
I followed the instructions for Getting Started with the NRF9160, activating the iBasis SIM card, placing into the board and applying USB power.
The first issue...
Hi,
I'm trying to update the firmware on my nRF9160 development kit
I downloaded the modem firmware and DFU tool
And then tried to follow these instructions: ...
Hi,
I want to activate eDRX on mqtt_simple example and measure the current consumption. I guess based on the code, by enabling "CONFIG_LTE_EDRX_REQ" it will be activated...
Hi guys,
I know that there is no official support for C++ on NordicSemi side, but I just wonder if it would be possible to work with C++ in Segger IDE. I'm trying to integrate...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
SoftDevice: s140
--
Hi All,
I use ble_app_blinky example and Android nRF Blinky SDK to add new function.
Recently...
Hello,
I'm using NRF52840 module to make a customer device. This device send message by UART. My device is powered with a battery, for this reason I would like reduce the...
Hi All,
We are using NRF52832 in our project. We have implemented the c code to perform nrfutil operations.
We are following below steps to do it.
Erase all files...
Hi, I'm doing some tests with Legacy OOB and I made it work with Master Control Panel 3.10.0.14, but when I try with nRF Connect v2.6.2 it fails. I know MCP is not supported...
Hi nordic,
Please inform bjorn-spockeli to reply in this thread its very urgent
https://devzone.nordicsemi.com/f/nordic-q-a/45470/encryption-and-decryption-of-advertising...
i working on a project of buttonless dfu on nrf52832 dk. so face a problem that after dfu the uart service is not show on nrf connect app. so i not be able to receive data...
Dear Technical Team,
I would like to check the more detals as following from you.
We shipped this part NRF52810-QCAA-R 60pcs to the customer, but they said they found...
There are several topics already exist on this forum concerning the attribute reporting, namely:
https://devzone.nordicsemi.com/f/nordic-q-a/42171/zigbee-attribute-request...
