after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
NRF_CLOCK->TASKS_HFCLKSTART = 1; while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0); NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
I finally figured out the problem with my custom board...
Hi,
I am using nrf52840 to run as an hci controller over UART for nrf91. I was able to implement FOTA over BLE for nrf91, but I would also like to add an option to add FOTA...
Hello,
I'm trying to configure the GPIO pins on the MDBT42Q-P192KV2 module, but they are not responding as expected.
I'm using the nRF52840 Development Kit to flash the...
Hi,
The errors that need to be resolved are as follows, and I think the sdk is not installed properly:
1.Please help me troubleshoot the installation problem of nRF...
nrf5340_audio application ， unicast_audio and broadcast_audio samples in zephyr， Are these all LE_2M by default ?
If I want to use LE_1M, how to change ? Modify prj.conf...
Action for Loading configuration is bugged. It Exports .overlay file but when Loading it only accepts .json file and it doesn't allow you to change it. Therefore, the file...
Hi I have recently bought the product nrf52840 from Digi key, i have dumped the code so many times but now days it is showing the error. the issues is whenever iam trying...
I'm using UART peripheral sample on an nRF52840 and SDK ncs v2.4.2. The Nordic module switches on another device (called UUT) which connects to its Rx and Tx pins.
I discovered...
Hi,
I am new to BLE development. I am using Visual Studio Code and Nordic SDK v2.7.0. I had working code a few weeks ago. I went on vacation, and when I returned I had all...
We are developing on the nRF52 Development Kit (nRF52 DK) for the nRF52832 SoC. Our application involves a 4-wire pipelined SPI communication with the Intan RHS2116 chip....
Hello,
I am encountering difficulties connecting to and recovering my nRF52840 board with J-Link on macOS, both via nRF Connect and using nrfjprog in the terminal. Below...
Hello,
We are using the nRF52840 dongle (PCA10059) with the CLI agent software as a Zigbee network coordinator, and the Digi's XBEE S2C as a Router.
We are using XCTU...
Hi Team,
I have nRF5340 DK board and I want to test the Bluetooth Periodic Advertising with Response and Bluetooth Periodic Advertising with Responses Synchronization...
Hi,
I am trying to create a new custom service in nRF Connect for desktop and play around with its characteristic properties.
I Use an nRF52840 DK as peripheral and my...
