I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
We are going to FCC lab shortly to certify nRF51822 BTLE. We have done this before on previous products and passed with the same radio block. Unfortunately our compliance...
Hi. I'm currently using nrf8001 and i need to send data consecutively and as fast as possible.
Connection interval used: 20ms
Data payload: 20bytes
Service pipe used...
Hello.
I'd like to set up my Secure DFU bootloader so that bonding is required to activate the bootloader from a peer device (phone). But at the same time I'd like to make...
I am using the secure DFU bootloader without bonding. Sometimes it DFUs successfully. Sometimes it produces this. I notice there is an error 0x200204, which I believe implies...
Hi I`m new to nrf so pls forgive me if this been asked before. 1. nrf52840 dk. Flash twi_scanner_pca10056 via nrfgo, verify ok.
2. At the moment I have no I2C devices connected...
Hello! I had asked a question about zigbee to parsing xiaomi data here . But there is no answer for my last ? .
tomchy adviced me this solution:
...
- register an endpoint...
Dear Sir, we are developing an application on the nRF52840 kit with SDK 15.0.0. We are using Keil as compiler. In our application we need to receive data from two uart together...
I have a test program that does a simple call to fds_record_write() to write a 4 byte value to an FDS file. This is using the NVMC backend. I happened to stop the debugger...
Hi!
Can anyone from Nordic pinpoint where exactly in buttonless project or bootloader project NRF_DFU_SVCI_ENABLED definition is used? I mean 15.0 and 15.2 SDK.
I have...
Hi, i need an advice.
It said in nRF51822 datasheet at p.11.1 (PCB guidelines) that "The supply voltage for the chip should be filtered and routed separately from the supply...
I have upgraded to the more recent J-link RTT Viewer.
If I start Debug Session in uVision and run RTT Viewer, I can connect just fine and have checked the Existing Session...
In the nrf5 sdk (version 11.0.0) there are three different modules which, as near as I can tell, do the same thing. These are:
pstorage
fstorage
ble_flash
...
hi........... nrf523
how to read the data from peripheral and send the data over ble using ble uart
i have merged the two programs ble_uart and twi sensor ,what changes...
Hi,
I'm trying to flash the mesh lightswitch example on Bluemod S42 custom board, please help me with what are the steps to be taken to flash on custom board.
