i want to advertise my one device into coded and into another device i want to do coded distance measurement it is possible to do in nrf 52840 version 2.5.1 ?
Hello! I'm looking for a way to include fast charging capabilities in my product, while still allowing USB2 data to pass between any host PC and the nRF52840. As I understand...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
We have encountered a problem in using iic to communicate that the delay cannot be removed.
We are using the sample in NCS,
the address of the sample is C:\ncs\v2.6.1...
Hi Nordic,
We are develop a multiple switch button device based on nRF54L15. We've two issues now while developing.
1. Matter Network Commissioning Issue with nRF54L15...
NCS 2.9.1 - NRF5340DK
I am trying to use multiple compare channels on Timer1 such that an interrupt handler fires for both compare values, the second of which is enabled...
Hi everyone,
I am currently studing to flash the MDBT50Q-DB-40 demo board from RAYTAC. I used the following site as reference. https://docs.nordicsemi.com/bundle/ncs-latest...
Hello,
I have always been able to use VSCode to find various installed toolchain versions, but today I suddenly cannot find toolchains other than v2.2.0.
I checked and...
We are trying to add CarbonDioxideConcentration cluster in matter. we are able to add temperature and humidity clusters and values which are updated are getting read in chip...
Hi
I have a beacon sending out some data, and I have already finish the TX side, I also want to have a RX side to receive the data, in addition, as there are many other...
Hello,
Im trying to security connecting but i'm getting this bug.
After auth_passkey_display(), Next step is so late(more then 3min).
Tool : VS code
SDK : nRF...
GNSS not working on Thingy:91 after modem_shell flash — help and gnss start return ERROR
Device:
Thingy:91 (NK-THINGY91) RS Stock No. 196-3901 nRF9160 + nRF52840 combo...
Hi Nordic,
I’m new to the nRF Connect SDK for VS Code and currently evaluating the nRF7002 DK board. I’ve been able to build and debug firmware successfully for the NRF7002DK_NRF5340_CPUAPP...
Hi,
I'm working on an indoor positioning system using an nRF5340 and a CHW1010-ANT1 antenna array. I'm receiving IQ samples from BLE CTE packets and using them to calculate...
Hello,
I would like to ask how to update the appName field in the shadow register on the nRFCloud, using CoAP protocol.
I was able to change the appVersion by passing...
If you see i'm trying to install toolchain and nrf sdk v2.6.1 via vscode, the installations seems to be successful but at the end of toolchain as well as sdk installation...
Hi, In my project we are using the ESB between a nrf52811 and a NRF5340dk and are trying to evaluate the maximum speed we can reach with ESB packet transmission without acknowledge...
Hi Nordic team:
I am configuring a low power application for the nrf52833 board (custom board). This is a very low power application and I want the board to stay on sleep...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Advertiser...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
I have compiled code that debugs and runs normally on the nRF52840DK. I just connected my custom PCB to the debug out connector on the DK and I have two issues that are probably...
