Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Greetings,
we have a custom pcb with nrf9160 and are using nrf-sdk v1.3.0 and mfw v1.2.0
Sometimes when connecting to lte the code crashes:
The code in question is...
Hello, I am developing with: custom nRF52810 board, nRF5 SDK 17, S112.
I'm using APP_TIMER for my main tick. I have the following code I use to initialize and start the...
Hello,
I am using SDK16, Softdevice S140 with SES.
I am trying to add DFU functionality in my application and leaving only the activation of the new firmware to secure...
Hello,
I am now working on a product concept which uses RTC module to retain date and time. To speed up the development, I started with ble_sdk_app_template and I am modifying...
We're using nRF52840 with S140 SoftDevice (version 7.0.1) and 16.0.0 SDK. When USB cable is connected before USB initialization we receive correctly APP_USBD_EVT_POWER_READY...
I am very new to the Embedded world and very confused about some stuff, I have searched the internet for 8 hours and then asked here.
I am being assigned to the task of...
Hi!
I'm developing application on nrf52832 development board which will be a work indicator - for office desk ;) Main idea is that i have client based on nRF MCU and desktop...
Hi, I am searching the nRF52810 product spec and see that with standard drive, maximum GPIO output current appears to be 4mA. However, this spec is given for when the output...
Hello, I am working on SDK 1.3.0, I have an NRF9160DK and I am migrating to a custom NRF9160, I would like to output the log by moving the pins of the UART. However, it is...
We have ported from SDK v15 to v15.3 but now have a problem getting the USBD to start.
Below is a sort of pseudo-copy of our USB init routine which is working for us on...
Hi,
On Nordic SDk 15.0, I have observed that USB CDC ACM Example is not working in interrupt mode on nrf52840 Evaluation kit.
But I have tested USB CDC ACM Example in...
I'm experimenting with nRF52840 DK
However, using break points in the main loop causes 'app_error_fault_handler'.
using the iar compiler. What's the cause?
Hi~
I have a question about the SAADC.BLE Connect Mode. When I turned on Saadc LP mode, the power dissipation was 0.02mA for single-channel sampling, but 0.5mA for dual...
Hi All,
I have looked through the devzone and cannot find a solution to this. I am using the nRF52832 SDK 15.2. Working with a BNO080 IMU over TWI.
I need to read more...
