I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Hello, We have a custom board with nRF52832, using BLE, s132. I have noticed recently that in nRF Connect App (v4.29.1) usually the services and characteristics show up twice...
Hi there,
I am trying to develop a simple application that must write information within a micro SD card (nothing too fancy, it is just plain data read from the internal...
Hi,
I added MCUboot and SMP BT Service to the OpenThread CLI routine to implement the device firmware upgrade function.
I found that after DFU is completed, the Thread...
If the lock's status changes while the device is powered off, causing a mismatch between the lock and the Apple Hub, how can I immediately update the status upon powering...
Hi!
I cannot get I2S echo sample to work on nrf54L15. Tried following overlay
build configuration nrf54l15pdk_nrf54l15_cpuapp
I verified with oscilloscope that no...
Hi,
All-of-a-sudden I'm having problems debugging my application. THis morning it was working right, this afternoon it's gone wrong!
I think it's pretty near using up...
Hello,
we want to get three different states using only one GPIO:
1. nRF52840 GPIO output driven low
2. nRF52840 GPIO output driven high (3V3)
3. nRF52840 GPIO internal...
Hi Support Team
UART20 of nRF54L15 can't work when setting P2.02 as TXD and P2.00 as RXD when I test the central_uart sample of NCS V2.9.1. I find that the SPI00 has used...
Hello Nordic community,
I'm working on a project using the nRF5340DK where I need to achieve precise control over three GPIOs with the following specifications:
P0.07...
Hello,
We are using the nRF52840 on our own board.
When I added up the current consumption at 3V, based on the datasheet, I get 14.3mA (CPU from RAM, Tx at 0dBm 1Mbps...
Hello,
I'm using peripheral_past sample on nrf5340 audio DK board, and select nrf5340dk_nrf5340_cpuapp_ns for Build Target.
I added the following config to enable RTT...
Hello,
I have nRF9160, modem FW = 1.3.6 and nrf sdk version 2.7.0.
I am trying to create an outgoing socket with connects to specific port num and ip address but I am...
Hello, I am working on a project where we use MCUBoot.
Currently everything works fine, but now we wanted to introduce persistent storage of some key value pairs.
For...
Hi Nordic Team,
What is the difference between 10 bit, 12 bit and 14 bit operation mode and 8/10/12/14 bit resolution in SAADC of nRF54L?
Best regards,
Bhavya
