Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello,
I am trying to make an application with three dongles and one DK. This application consist on control the 4 LEDS of the DK, and each LED is controlled by one different...
I have encountered two issues while using the NRF PWM driver on the nRF52 DK, with or without SoftDevice S132, along with SDK v11.0.0
The first one is the use of the NRF_DRV_PWM_PIN_INVERTED...
I'm building a COAP client using the Nordic nRF9160DK cloud coap-client example code as my base. I have the UDP version working great. But I'd like to convert to TCP.. I was...
Hi all, I have an odd issue with an iphone XR. The NRF Connect for Mobile application can see adverts from the device when scanning, but the device does not appear in the...
Hey! I'm trying to sniff the data moving between a Bluetooth LE button and a Central.
Installation of the Bluetooth LE Sniffer went pretty smoothly but Wireshark only shows...
Hi,
I'm trying to use a nrf delay to make a delay for a motor. The idea is to make the motor oscillated by putting it forward and then reverse via a delay. (you can find...
Hello,
I need to run "west build" and "west flash" commands from my custom IDE/Editor. If I open up Toolchain Manager and then do "Open bash" or "Open Command Prompt", ...
Hello,
I am trying to do directed advertising while us ing the coded PHY whithout bonding the devices but i am running into some problems.
The device with the BT-address...
Hi,
I use nRF5340DK (0.11.0) as HCI controller and noticed it can randomly (?) accept PDUs with access address other than configured. This basically makes it impossible...
Hi,
When I build CLI sample in nRF_Connect_SDK, I don't get any USB port for CLI.
I believe the sample is in default mode built for UART.
How to build this for USB,...
Hello. I can't normally use USB for two-way communication.
The problem is sending the PRX payload in ACK packets.
After conducting a simple test: PPTX sends a packet once...
Trying to use the basic baremetal mode as my application is very simple and dont want to go through RTOS stuff.
I tried with Timer and RTC, both case if I enable the interrupt...
I am using the nRF 52840dk board and I am new to nRF, I had worked on Cypress CYBLE & CYBT-343026-01. I am starting my development for basic BLE transmit, eventually, I am...
Dear Nordic experts, How do you verify that a (mesh) firmware has an app key assigned? What I'm looking for is basically the Mesh SDK's version of NCS's bt_mesh_app_key_exists...
I used the alternate method of installing nRF connect described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.8.0/nrf/gs_installing.html#build-environment...
