Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
While compiling the custom project in nrf vs code , I am getting the following error;
Configuring incomplete...
Hi,
1. As shown in the following figure, how to resolve such a default instance compilation error?
2. I have used west update to confirm that ncs v2.9.0-rc1 is successful...
Hi,
I have a nRF24L01+ as the TX and have lots of existing nRF24L01+ RXs. I would like use the nRF52810 as the RX as it saves the need for an MCU and on BOM parts. The current...
The text for the recommended nRF Connect SDK workflow (using a Workspace Application Repository - https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/dev_model_and_contributions...
Dear Devzone:
I have setup done matter environment as blow:
NB: Ubuntu 22.04 with WIFI and BT, installed CHIP tool from official pre-built (V2.8.0 corresponding version...
Hello
Our customer makes IoT Product and use the Nordic 9160.
However the PCB Size is small.the 9160 SiP design in the PCB Top layer and Sim Card design in the Bottom...
Hello
As the title says, I am suspending the UART using PM_DEVICE ACTION_SUSPEND, but the power consumption is not decreasing significantly.
With CONFIG_SERIAL=n and no...
Hello. I'm trying to toggle a GPIO pin at a predefined frequency in order to measure the accuracy of out RTC clock. This code uses the GPIOTE, RTC, and PPI peripherals in...
We are evaluating the the NRF 5340 for a new project and we would like to know if the NVS implementation [1] provides protection against data corruption if the supply is unexpectedly...
Hi guys,
So, I've been working on a project for measuring liquid using the TDC1000 IC from TI which was running fine on STM32.
My experience with nordic connect sdk is...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
Our pre-production PCB power consumption still too high, so we are looking for a way...
Hello, I have a Thingy:53 sensor hub application (extended the Nordic Thingy53 Sensor Hub blog to include IAQ sensor) built under NCS v2.7.0 that runs fine.
When rebuilding...
In the link process between Central and Peripheral,
sometimes Link processing does not work correctly and the following log output: . cis_gateway: Discovery failed: 14 ...
1. After DFU has successfully completed the watchdog fires. I know this because my App picks it up from the register, however I'd like to use this bit to indicate a potential...
Hello,
I am designing a PCB using the nRF54L15 and a ceramic antenna and got confused regarding the impedance-matching network. In the detasheet a 1.5pF, 2.0pF, and 0.3pF...
