Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
We are facing an intermittent issue on an nRF52832–based product using bare-metal Nordic nRF5 SDK (non-NCS, non-Zephyr) BLE implementation.
Observed behavior:
BLE initializes...
Hey,
I am plannign on developing a locator tag and I wanted to find some more precise information on when to use AoA and AoD and if it changes the accuracy drastically....
Hi,
I need to save a 16 bit counter into a retained register.
I cannot use the 2 GPRETREG since they are already used and I cannot write internal flash.
I cannot use...
Hi everyone,
I’m facing a linker issue in NCS v3.0.2 while using the Zephyr HTTP client sample with TLS enabled , and I’m looking for guidance on the correct configuration...
Hi all,
On a BLE project I was working using version 2.5.0 of the VS Code dev environment I was able to set up a partition where I could store non volatile data, such as...
Hi guys,
I've been using the ADC with the internal reference of 0.9V.
However, to increase the scale of the ADC without using the gain 1/4 I've made a revision to the...
Hello,
we are testing the BLE ADV capabilities and also MESH performances on NRF54L15.
We verified that, in conditions of continuous scanning (interval = 30ms), the packet...
Description: I am implementing USB Mass Storage with a FAT filesystem on external MX25UW63 flash (via EXMIF) using the nRF54H20 DK (NCS v3.2.0).
Setup:
Board: nRF54H20...
Hi Nordic Community, I am working with the nRF52833 and I have a question regarding the electrical characteristics of the dedicated USB signal pins (D+ and D-) when the USB...
I thought that the nRF21L01 had been obsoleted and replaced with the nRF21L01+, but digikey doesn't list the + version but still shows the old one for sale. Has the part been...
I'm sending HCI command LE Set Transmit Power Reporting Enable with both local and remote reporting requested.
The Bluetooth Core Specification says "If the Remote_Enable...
On nRF54L15 DK (CPUAPP) the app boots and advertises fine, I bound my phone using nrfconnect but when I reboot the DK and try to reconnet using nrfconnect, the device hangs...
I have a new nrf9160dk board that I will be using for a BLE customer application. I am using zephyr/samples/bluetooth/hci_uart SDK V3.2.0 to be loaded into the nRF52840 in...
Hi Nordic
We would like to be able to read out the serial number off our devices, without connecting to them,
We have not enabled RFID on the product, but would like to...
