I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hello,
I am trying to program a custom device of nrf54l15 using nrf connect for desktop app(V5.2.0) -> Programmer(V4.6.2)
I am able to program it but this is how I see...
I am bringing up a custom board using the nRF54L15 (Fanstel BM15M module) and I am using SPIM00 as the high-speed SPI interface. I am configuring the peripheral through Zephyr...
Using PPK to measure the current, it was found that there was a 1-minute cycle signal in the current waveform. No timer was set. The watchdog timer is 10 seconds.
Im currently working on a project which should receive audio through CIS and retransmit it over BIS. Im using nrf5340_audio_dk for this. Ive tried using https://docs.nordicsemi...
Hi,
We came across this feature " PLMN selection optimization during initial search ", enabled by AT%FEACONF=0,3,1 . It sounds good for speed and power consumption.
...
Hi all,
I’m working on a custom board based on the nRF9151 , and using the Ignion NN03‑320 antenna for GNSS reception.
In our GNSS TTFF testing (using AT commands),...
I'm developing a keyless entry/start system for vehicles with the following requirements:
The vehicle side uses an nRF54L15, while the mobile phone is a standard smartphone...
Hi,
I am developing an audio application on nRF54L15. I have successfully used the Zephyr API to read sequences from the ADC with extra samplings (the "extra samplings"...
Hi.
Goal I am creating a new application for the nRF54l15 and want to follow the latest recommendations for project configuration. I need to do DFU over BLE, so I'm trying...
Recently I noticed (for reference in the NCS/v3.1.1 SDK) that some nrf9151 boards are in zephyr folder structure and others are in the nrf folder structure.
NRF9151DK...
Hi support:
When testing the peripheral nfc pairing sample on the nRF54L15-DK development board, and using an Android phone for testing, it was found that...
Dear Company
We are using the following component NORDIC NRF52840-CKAA-F-R7 and we have a problem in the test phase.
We have two version with the following marking code...
Hello,
I’m working with the nRF9151-DK hardware to test Power Saving Mode (PSM) functionality, but I’ve encountered an issue: The TAU timer (T3412) cannot be activated,...
Hi
Nordic engineer
Power consumption cannot be reduced after using hardware encryption. Under normal conditions, the device power consumption is 30µA, but after calling...
