I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
We would like to interface an external PSRAM with nRF5340 MCU.
We didn't find any refference on how to do so.
So, my question is it possibel to interface...
Hello,
I'm using nRF9160 and modem firmware version 1.3.6.
I'm using %XRFTEST command to measure RX power received by modem. Command documentation can be found here: https...
I have been through the devacademy lesson on custom boards and am using the nRF53 so have used the custom board for multi-core approach. The example uses the 9151 which has...
I'm trying to add MSC functionality to my project, but I'm encountering the following error:
To understand the cause of the error, I tried creating a new application from...
Hi Nordic Team
We develop a sensor node for a customer based on nRF5340. For now I use a nRF5340DK to do my tests with NCS 2.8.0 (using VS Code).
Based on examples, I...
Good Day,
We have an ongoing project that uses an RP2040 MCU (with FreeRTOS) and we need to add WiFi capabilities to it. It needs to be dual-band and fairly high throughput...
Hi all,
I'm currently working with the nRF52 DK (nRF52832_xxAA_REV3) using the nRF5 SDK version 17.1.0_ddde560 and the IAR Embedded Workbench - Arm 8.32.3 IDE. I'm facing...
Hi Team,
I just want clarity on 2 points related to accuracy of nRF9151 GPS.
1) As shown in datasheet, "Positioning accuracy (CEP50), periodic tracking" is 3.4m. So that...
Description: I am encountering an issue while testing the watchdog functionality. When I intentionally hang the system for longer than the configured watchdog timeout period...
Hello,
I'm new to software development so apologies if this is a simple question but I can't find a straightforward answer for nordic connect sdk on vs code.
An IC I...
How can i configure the nrf52840 dongle with DHT-11 sensor such that i am able to use it to send the temperature data via UDP within the Thread Network? I am using the NRF52840...
Hello, I have used this template (ncs-example-application) to start developing my project. I've installed also all the prerequiries to use the application using command line...
I am using the existing nRF Connect SDK (v2.9.0) example of Wi-Fi provisioning using Bluetooth LE ( https://github.com/nrfconnect/sdk-nrf/tree/main/samples/wifi/provisioning...
Hello,
I am currently testing a custom board using the nRF5340QKAA .
Most of the connections are the same as the nRF5340 DK , but the main difference is that I built the...
