I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello,
I try to figure out, how to correctly setup MCUboot for an nrf5340, so that:
Application is updatable
BT Stack is updatable
Firmware Updates are encrypted...
I am trying to enable a watchdog and then stop it. i closely followed the datasheet way to do this. the problem is that the watchdog once enabled will always fire. i want...
I'm working on nRF5340 custom platform (NCS 2.6.1, Zephyr 3.5.99). I use MCUBoot immutable bootloader and external QSPI NOR Flash for slot-1 partition during DFU.
This is...
Hi Nordic Team,
I am working on the Matter Smoke/CO Alarm example with ICD (Intermittently Connected Device) support enabled.
My operational mode is working correctly...
I'm trying to replace HM-10 module with a RAYTAC MDBT42TV-DB-05 for a transparent UART (serial passthrough) application. I've configured all the parameters and GATT settings...
in fact , I have the while sdk directorys. in c:/ncs/v3.1.0 but,the nrf extension in vscode cannot recognize it. it always info me to install a sdk in welcome page. so, I...
I am using nRF52840, we have an issue which seems like a standard issue with nordic switching between regular battery and a coin cell backup.
I need to know the following...
Hi Support Team
Is the ifft the measured distance? I test the channel sounding sample in NCS v3.0.0 and find that the ifft distance error is relatively large. How to optimize...
My new PC could not find PPK in the power profile menu, even I installed different version nRF connect desktop or different Power Profile versions. I always could not find...
Hi:
I'll be using the Raytac Bluetooth Module in my project.
Imagine that the Bluetooth Module has a Bluetooth connection established with the smartphone (Android or...
Hi,
I am programming with ncs v2.9.0 based on nrf52833 chip
And base on peripheral_hid and central_hid
Testing that peripheral send data continuesly to central,and about...
Hello
I am attempting to perform BLE certification using a third-party module for the nrf52832.
Should I select the nRF Connect SDK QDID for all design items?
Or, should...
Hei,
I want to implement custom AT commands using a nrf9160 and ncs 2.8.0. The device should be able to process custom AT commands via UART console.
I followed this documentation...
Hello, I am using nrf52832 along with S132 soft device and SDK 17.1.0.
For BLE pairing I am using Just Works as there is NO IO and NO Display.
Could you please confirm...
