Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
I have a situation where I need to sample from multiple channels using SAADC on a timer (similar to maximum performance example). However, the added catch is that at the end...
I am using a Asus Vivobook S15 notebook which uses arm64 architecture. The Power Profiler Kit 2 is not recognized.
Is the PPK not compatible with arm processors?
We have a very successful wireless MIDI transceiver with the NRF24L01P for more than 11 years, used by stars like Chic Corea, John McLaughlin and Herbie Hancock. Now we are...
Hey,
I flashed the actinius icarus board (nrf 9160) with the at_sample application, successfully sent the modem to sleep using "AT+CFUN=4" command with the Serial Terminal...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. I am checking the operation of "Scheduler Server". The registered schedule was changed to inactive, but...
Hello everyone,
I am a college engineering student working on a circuits project, and I need some help. The project is to design a proximity device that sounds an alarm...
Hello,
we are using a Flutter App on iOS and Android.
With iOS the data transfer is as fast as expected, but Android seems to have delay of 2 seconds between the data...
I am adding a bootloader to my project for OTA DFU.
App core and net core update was successful in the 1st stage bootloader configuration, I'm configuring a second stage...
Does the NCS stack + nRF7002 support scanning while connected? I would expect it could, to support handoff, but getting errors.
Using nRF7002-DK and NCS 2.8.0.
Compile...
Hi, I have an issue when I try to install the nRF connect SDK. I am using Linux Fedora 39, trying to isntall SDK v2.5.0. Steps taken so far:
Download and install nRF command...
Hello! I was wondering if there is any advice from trying to get Non-simultaneous firmware updates using sysbuild with the following constraints:
Must update both App...
Hi,
I am having problems getting PSM mode, or at least getting a decent power consumption in PSM mode, because I think the PSM in working properly.
I am using the EVB...
I am using Zephyr to create a program that integrates BLE Mesh and NUS. My goal is to use a sensor_client to read data from a sensor_server, and then send the data, via peripheral_uart...
I using a BMI323 sensor with address 0x68 on the I2C bus and a custom-made nRF52832 dev kit. when I tried to send some commands to the sensor via I2C, it didn't work.
here...
Hello, I'm writing an application for nRF91 series and I have the functionality mostly working but the "sleep" current is high, about 4-7mA. I assume that this means that...
