Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I'm writing an application for the nrf5340 with nrfConnect v1.6.1,
I've been able to do the FOTA upgrade through BLE with the example smp_srv located inside zephyr/samples...
I recently got the nRF52840DK and have been able to build/flash a couple simple samples. However when attempting to try the OpenThread CLI example on tool chain v1.6.1 and...
Hi,
cannot run pc-nrfconnect-launcher v3.7.1, built from sources.
```
$node -v
v12.22.5
$git clone https://github.com/NordicSemiconductor/pc-nrfconnect-launcher...
Hi,
When I want use nrfjprog to program my NRF52, I have a problem.
This why I write to program my nerf : nrfjprog -f nrf52 --program _build/astronaut.hex --sectorerase...
Hello,
Is there example code on how to get NRF_SAADC_INPUT_VDDHDIV5 working? When I do nrfx_saadc_init(), I get NRF_ERROR_INVALID_STATE.
Same code works fine with normal...
I am using nrf5340 and icm20948 for our development. i had initialized things as shown in code attached.
this work fine for me. but when i am uncommenting rc |= inv_icm20948_enable_sensor...
Is there any guidance on zigBee OTA? What are the similarities and differences between ZigBee OTA and BLE OTA? Could you please tell me what I need to pay attention to during...
Today I received my first CMSIS-DAP debug probe (Pitaya link) and tried to integrate it into my development environment. Unfortunately, I must have broken my Pitaya Go (Nordic...
Hello,
I've been very slowly gearing up towards developing for the nRF9160. I'm going through the "nRF Connect SDK Tutorial"
https://devzone.nordicsemi.com/nordic/cellular...
For example, I'd like to add at_cmd_parser to my project. It's under /ncs/nrf/lib/at_cmd_parser.
My project is out-of-tree in its own directory. Initially I tried add to...
Hello,
I am using example code of LIS2DH ac celerometer sensor with nRF SDK v1.3.1. Building the example code I am getting macro error in devicetree.h file as mentioned...
Hello,
I am using PPK 1 kit with nRF52 DK. The system is used to measure the power on nRF52840 DK using DUT mode. The system was working just fine until I started receiving...
Hi
I'm trying to use the nrfx TWI Slave function with IRQ (No Poll), but there is no clean code available I found.
I'm using the following code:
But even if I can...
Hello,
I am using NRF9160 running the Serial LTE Modem application in NCS 1.5.0. When connecting with AWS IoT over a secure MQTT connection the maximum MQTT packet size...
I'm using nRF5340 to provide Bluetooth connection to other devices. Almost all Android devices connect correctly, for example: Samsung S21, LG G8X, Xiaomi Mi Mix 2. However...
