Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi, I've got a project runing fine on v1.5.1 but will not update to v1.6.1 with this west.yml file: changing the revision v1.5.1 to v1.6.1 to keep up to date with the sdk...
Hello,
I am using nrf52 DK to program an nrf52805 with the ESB protocol. My nrf52805 is in slave mode compared to a micro Stm8l serial connected.
I'm having trouble configuring...
Hi everybody,
I am working in a project where there are one central_UART with multilink and diverse peripheral.
The devices are a custom board Fanstel BC840, nRF Connect...
Hello ;
We used NRF9160-SICA-B1A-R in our project. We have to choose the old version (NRF9160-SICA-R7) as NRF9160-SICA-B1A-R is out of stock. the only difference, Some of...
Hello,
I am attempting to implement cell tower triangulation using unwiredlabs.com's api.
I have single-cell geolocation working. I am having trouble getting multi...
To measure the antenna in band 20, you can send a carrier in the frequency range from 832-862 with the command "AT% XRFTEST = 1,1,20,8320,0,1,4".
To measure the antenna...
Hi,
I am using nRF Mesh SDK 4.1 and nrf SDK 16. I started with the light switch client example on a DevKit.
I am trying to change the publication address of the client...
Hello, DevZoners!
Hope you all doing great!
I have 2 9160DK's and for a few weeks now I've been trying to connect to the LTE network and then connect to the nRF Cloud...
I have changed the ram start and ram size, but as soon as i am adding the 10th characteristic to my second custom service, the program is crashing? i've also changed BLE_GATT_DB_MAX_CHARS...
What is the maximum file size of the LTE Modem firmware update we can expect on the 9160 platform? I am trying to plan out our external flash size and partitions.
The...
I recently switched from 1.5.1 to 1.6.1 and I'm now finding the SLM is misbehaving.
When I try to send a large payload such as 933 bytes of data, I find the CTS signal goes...
I successfully built, run and tested the sample: gps on my nRF9160 DK , without using the SUPL client library.
I then tried to build and run this sample: gps with the SUPL...
Hello,
I have been asked to research a possible solution to add support for executing REST calls to the AWS cloud. I see a library and API for making REST calls to nRF Cloud...
