Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hello,
For the vias in the exposed pad of the NRF54L, I've read that ideally, the vias should be capped and filled. However, due to trying to minimize cost, I was wondering...
Hello everyone,
after some months, yesterday I used my PPK2. When I plugged in and I opened the Power Profiler App, a pop up required me to update the device firmware. ...
Hi,
We had a nRF52840 DK board developed off Hardware files v3.0.3 build. The manufacturer didn't have any of the MCU or SEGGER J-Link debugger files on the device. We are...
I added a cmake configuration option to CMakeLists.txt, but sending a value through west build does not set the cmake option. Here is what I have done: CMakeLists.txt
The...
I am using an nRF52840 dongle as a sniffer to capture BLE packets in Wireshark. Recently, I’ve noticed that the captured files are approximately half the expected size, and...
Hello,
my nRF9151 DK appears to be damaged or has a power-path failure.
Current symptoms:
No LEDs light up
No J-Link is detected
No COM port appears
No mass...
I'm stuck implementing encrypted firmwares on the nrf5340, ncs 3.0.2., with NSIB and MCUBoot. I got signed DFU to work as described in Exercise 3 – DFU with external flash...
I noticed from the design guide that the voltage tolerance of capacitors C3 and C10 is 10V. Can I choose 6.3V for the voltage tolerance of these two capacitors? Will this...
I am developing an indoor positioning system using Bluetooth Channel Sounding (CS) on nRF Connect SDK v3.1.1 . My setup involves one Initiator and four Reflectors .
Implementation...
Hi Dev,
Development platform: NRF54L15 + NCS 3.2.3
We are facing an issue with ADC sampling. The code occasionally gets stuck/hangs inside the adc_read function. This...
Hello,
I am currently testing the Release Assistance Indication (RAI) feature on the nRF9151 (SMA-DK) in order to minimize power consumption after data transmission.
I...
Hello, I'm following BLE fundamentals course from Nordic Academy. İn Lesson 4 Exercise 3, with using Nordic UART service. We sent and receive data. However i'm having problem...
Hi everyone. I’m currently working on a custom board based on the nRF5340, but I’m unable to connect to the board when trying to flash it via the SWD interface using J-Link...
Hi all,
During the Bluetooth connection process, there is a small probability of the following phenomena occurring (both of which are the same firmware, with the similarity...
Hello DevZone team, I recently received a new nPM1300 Eval Kit (PCA10152, 1.3.0, 2025.19) and connected it the first time following the documentation ( docs.nordicsemi.com...
