I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hi All,
I'm currently working with a custom board using the NPM1300 and STM32L4, alongside the npmx drivers. I'm trying to capture both pressed and released events from...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I want to configure P1.02 and P2.06 as normal GPIO for my nrf54l15 custom board. For this I have added the following in my .overlay file
From https://devzone.nordicsemi...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hi Friend,
I am using nRF54L15-DK,NCS2.9.1 to drive INMP441 to collect voice. I take the I2S_echo Zephyr example as base. I can found the config a s below but it doesn't...
Hi
I am working on a BLE repeater which is central and peripheral application. which will scan and connecting with sensor device , and advertising for phone connection....
Hello Guys
I'm currently working on a BLE AoA (Angle of Arrival) application using the nRF52833 Development Kit . I’ve run into some challenges regarding hardware connectivity...
This is the command I used to generate setting.hex.The primary address of my app is 0x19000.
This is my hex distribution. The library used is nRF5_SDK_17.1.0_ddde560....
We designed a board based on the nRF52840, and are using nrf5 SDK 17.1.0 with S140 SoftDevice. We are using a QSPI flash, MX25U51245G ( https://www.macronix.com/Lists/Datasheet...
My task is to mount a littleFS system on the external flash memory, so I can save files.
I am using the littlefs filesystem sample from
zephyr/samples/subsys/fs/littlefs...
Hi everyone,
I’m designing custom hardware for my application using the nRF54L05 MCU (v2.9.0) . However, I can’t connect to the device from iOS — the connection always fails...
