I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
hi support team,
for nrf5 sdk ble_app_hid_mouse example, this example shows how to use swift pairing, it works. but I have one question for it, after I press reset button...
Hi, I'm trying to run samples provided by Nordic but I fail. My problem is west can not find my Jlink.
I can flash the chip (nrf52840 custom board) using nrfjprog
...
1. When I run the SDK routine provided by the official, ble_app_uart program, the circuit board acts as the peripheral , the protocol stack is pre-downloaded to the board...
Hi, I am new with nRF microcontrollers. I created a custom board that mounts the nRF52840 microcontroller. I made a firmware that uses BLE to exchange data and everything...
Hi,
I'm using nRF Connect SDK v1.7.1 with two nrf5430 DK. My goal is to evaluate the different security levels. For testing i send messages with the Nordic Uart service...
According to the AT command reference v1.7, the nRF9160 SIP modem firmware v1.3.1 added the %PERIODICSEARCHCONF command.
It does though not mention anything about the behavior...
We are evaluating OpenThread for a custom board with a BL654 from Laird, which contains an nRF52840. When running the OpenThread CLI sample from nRF Connect SDK 1.7.1 we are...
remoteproc_mgr_config() from nrf5340_cpunet_reset.c that is called during init by zephyr for starting main thread uses hardcoded pin numbers for uart with cts/rts pins and...
Dear Nordic Team,
I am able to perform a successful DFU on a development board pca10040 using the DFU library for iOS. The thing is that after the DFU process, the phone...
Hi, I am using custom board. i am facing issue when i am integrating with ble we are facing issue that i2c stopped working. event we are not able to read(scan) slave address...
Hey devzone community,
I have a problem in migrating my program from SEGGER to VS code,
the 6 tutorial work only on new versions of SEGGER.
there is a simple option...
Hi,
I'm using the nRF9160 DK board with nRF Connect.
I want to create a driver for an LCD with a parallel interface. SPI is to slow for my project.
First, do you...
I have a question on the gnss event type NRF_MODEM_GNSS_EVT_FIX. It seems there's always the NRF_MODEM_GNSS_EVT_PVT event regardless it's a fix or not. The flag can tell us...
I am writing a program for a Garmin Edge which needs to connect to a power meter via Bluetooth, some of the characteristic / service UUIDs are 4 digits which cannot be used...
Hello,
In the latest SDK version v1.8.0, I have developed my own project based on direction_finding_connectionless_rx demo. Here are two problems I countered.
1. the RSSI...
