I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
is there a way to hide the west project from the Git view in VS code? Sometimes you just don't need to view any changes related to west and it's getting quite messy...
I am working on a Zigbee network using the nRF Connect SDK and need to retrieve the link quality information (LQI) of a specific device based on its short address. What ZDO...
Hi,
I have used nordic documentation a lot few years ago, and I am looking for BLE sequence diagrams especially the ones during pairing process with LE Secure connection...
Good morning,
currently we are on ncs SDK v2.7.0.
Because SDK v2.8.0 supports the KMU in MCUboot on the nRF54L15, I updated immediately and gave it a try.
Unfortunately...
Hello,
I searched but I can't find how to retrieve accelerometer data with thingy:53 and then send it via bluetooth to nRF Connect on phone?
Can you help me
Thank...
Hi,
I have opened sample "Peripheral_hr_coded". I have build it successfully. I click on debug. I expect cursor would start from Main function. But Debug was not started...
I'm developing my application using the NRF Connect SDK in VS code. SDK Version 2.4.2. The NRF52832f we're using is integrated into a module made by fanstel and it has been...
Hi,
I am going through the DevAcademy Bluetooth LE lessons, using nRF5 DK. But I run into problems directly in the exercise of the first lesson. Everything goes fine to...
Hello Nordic community,
I am currently working on developing applications for Matter over Thread and have set up my ZAP file accordingly. I've successfully flashed two types...
I want to use a switch in the overlay file, like:
To do so, I try to add a config statement in a custom KConfig file. (mp_Kconfig.conf):
Adding the file to the build configuration...
Hi,
We have come to expect that with the nRF Connect SDK installed properly and using recommended options we can build a sample, for example
$cd \ncs\v2.8.0\nrf\samples...
I am trying to complete the exercise, however, it seems that the only terminal output I receive is from whichever thread is run first, irregardless of whether I use k_yield...
I'm trying to setup an nRF52832 to drive 127 ws2812 by using PWM. It seems the bit-by-bit method is too slow for the 1.25uS period. pwm_set() is using somehow ~5ms, so that...
SDK : 2.6.1
uC: nrf5340
Hi,
how to avoid erasing of the application settings when updating the firmware via bluetooth.
When using the android version of "nrf connect...
I can program the spi and i2c find on my nrf54l15pdk board version 0.2.1, as soon as i turn on CONFIG_BT =y the device fails to do anything past being flashed successfully...
