I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Regarding the operation of EJ2832AA1 (nRF52832), Please answer the following questions. nRF5 SDK ： v15.3.0 SoftDevice ： S132 v6.1.1
I am doing UART communication with another...
Hello, I am new here and I hope to not duplicate any other similar post (to be honest I have search a lot before writing). I am working with nrf52840DK, I have used blinky...
We're trying to set up MQTT messaging between our custom nRF9160 device and our private AWS VPC. When using the Serial Terminal in nRF Connect for Desktop to monitor the device...
I am reaching out to request assistance regarding a FOTA (Firmware Over-The-Air) operation using the HTTPS protocol for my new nRF7002-DK development kit. I have successfully...
Hi
I heard about that RSSI has no relationship with disconnection. However, based on my experiments, the connection will break every time I am close to -80dBm.
I am confused...
Does anyone know of a good starting point for Bosch BHI360 IMU integration into nrf5340 and Zephyr?
Did look at: https://community.bosch-sensortec.com/mems-sensors-forum...
Hi,nrf52832 entered in bootloader mode.as ld5 led is keep blinking on power reset and holding if boot/reset button.please help me to get board back to normal mode.thanks.
I had previously gotten working code to communicate with my SPI device on the nRF5340DK w/ NCS v2.5.0 that uses the HAL SPI library inside TF-M. I used NCS v2.5.0 (nrf\samples...
I observed another user having this same issue with resolution.
It appears the watchdog configuration has changed but I'm unable to track down the driver/overlay/etc that...
Hello,
I am working on an nRF5340-based project where I successfully integrated the broadcast_source and central_and_peripheral_hr examples from SDK 2.6.0. Both functionalities...
Hello all,
I'm working on a localization system using the nRF52832 chip and Bluetooth Low Energy (BLE), but I'm running into challenges due to how BLE transmits signals...
Hello Team,
We are currently working with the nRF54L05 and using the nRF Connect SDK. We have successfully evaluated basic BLE peripheral samples on the EVK.
For our application...
Hi,
I am going theough the first lesson of 'nRF Connect SDK Introduction' course, have installed nrfutil and updated the path. When trying to install 'device' as per the...
Hi, I have this problem and I couldn't find any working solutions. I am developing my own hardware and there weren't any problems until I started to use debugger. My program...
Is there any reference information on how long (in ms) different steps in a BLE pairing process takes? e.g. Pairing Feature Exchange, Short Term Key Generation, Long Term...
