This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I was developing application very similar to the basic ble_app_uart_pca10040_s132 example when I started getting random restarts and Segger Embedded Studio breaks at a strange...
Hello all,
Lost my VM that had a working installation and just setting everything back up.
After installing SDK 1.8.0 and all of the extensions for VsCode. Now both SEGGER...
Dear Nordic experts, Considering a Bluetooth Mesh application based on NCS 1.7.1 and running on an nRF52832 : What steps need to be done to add DFU over Bluetooth LE ? Is...
Hi all,
I have an BLE application where i wish to measure the devices power consumption. I am trying to measure the affect of changing the connection interval, MTU size...
There is a previous similar question here:
https://devzone.nordicsemi.com/f/nordic-q-a/16382/switching-between-apps-with-dual-bank
I am using nRF5232, nRF5 SDK v16.0.0...
Hi!
I am working on a custom board and would like to use an external flash for BLE OTA updates. The FW is based on NCS v1.7.1 and MCUBoot as the bootloader. I would like...
Hello Nordic gang. I'm reading sensor data on the nrf9160DK, the sensors have a fifo with 96 entries. If I can't read the sensors fast enough, the fifo overflows and I get...
Windows 8.1 64-bit: PPK2 shows in Device Manager, does not show as an item in Power Profiler software.
The device works, as I've used it successfully on a Virtual Win10...
What is the difference between the Async Read ApI and the Normal Read API of the ADC ?How the ASYNC read API work ,can anybody explain with sample code. Specially thirds argument...
Hi, We have designed a custom board using nRF52840 SoC, now we want to calculate its power consumption I want to ask if we can measure custom board power consumption using...
I am trying to use the NRF52832 to connect to the BMA456 Accelerometer from Bosch using SPI and am running into the following issue:
All read/write commands work fine...
Hi, I'm trying to implement a timer that will trigger each 10ms (for example) an handler function and do something inside it. So, I came with the idea to implement an App...
Hello !
I would like to use pin P0.12 as common gpio output and configure it on quite later phase in my SW.
I use nrf_gpio_cfg_output and set/clear for have relevant value...
Hi,
I'm working on central_uart and peripheral_uart examples. I want to get the rssi value and tx_power of all advertising packets from peripheral to central via bluetooth...
